Introduction
This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of the FSP460-60GLN Industrial Level Switching Power Supply. Please read this manual thoroughly before using the product and retain it for future reference.
Safety Information
Always observe the following safety precautions to prevent injury or damage to the power supply and connected equipment:
- Electrical Hazard: This unit operates with high voltages. Do not open the power supply casing. Refer all servicing to qualified personnel.
- Ventilation: Ensure adequate airflow around the power supply. Do not block ventilation openings.
- Environment: Operate the power supply in a dry, well-ventilated area, away from direct sunlight, heat sources, and moisture.
- Grounding: Always connect the power supply to a properly grounded electrical outlet.
- Power Cord: Use only the power cord supplied with the unit or an approved replacement. Do not overload power outlets.
- Installation: Install the power supply securely within its intended enclosure.
Image: Close-up view of the FSP460-60GLN power supply's warning label, indicating electrical hazards and compliance marks. This label provides critical safety information and operational specifications.
Setup and Installation
Follow these steps for proper installation of the FSP460-60GLN power supply:
- Unpacking: Carefully remove the power supply from its packaging. Inspect for any visible damage.
- Mounting: Securely mount the power supply in the designated bay within your system chassis. Ensure all mounting screws are tightened.
- Cable Connections:
- Connect the main 20+4 pin ATX connector to the motherboard.
- Connect the 4+4 pin EPS/ATX 12V connector to the motherboard CPU power socket.
- Connect SATA power connectors to storage devices (HDDs, SSDs).
- Connect Molex connectors to other peripherals as needed.
- Ensure all connections are firm and correctly oriented. Do not force connectors.
- Power Cord: Connect the AC power cord to the power supply's AC inlet, then plug the other end into a grounded electrical outlet.
- Initial Check: Before powering on, double-check all connections to ensure they are secure and correctly installed.
Image: The FSP460-60GLN power supply unit, displaying its compact form factor and various output cables for connecting to a motherboard and peripherals.
Operating Instructions
Once the power supply is correctly installed and all connections are made:
- Power On: Flip the main power switch on the back of the power supply to the 'ON' (I) position.
- System Start-up: Initiate your system's power-on sequence (e.g., pressing the power button on your computer case).
- Power Off: To shut down the system, follow your operating system's shutdown procedure. Once the system is off, you may flip the power supply switch to 'OFF' (O) for complete power disconnection, especially during maintenance or extended periods of non-use.
Maintenance
Regular maintenance helps ensure the longevity and stable operation of your power supply:
- Cleaning: Periodically clean the exterior of the power supply and its fan grille to prevent dust buildup. Use compressed air to gently clear dust from the fan and vents. Ensure the power supply is completely disconnected from the AC outlet before cleaning.
- Inspection: Annually inspect power cables for any signs of wear, fraying, or damage. Replace damaged cables immediately.
- Environment: Maintain a clean, cool, and dry operating environment to prevent overheating and component degradation.
Troubleshooting
If you encounter issues with your FSP460-60GLN power supply, consider the following:
- No Power:
- Check if the AC power cord is securely plugged into both the power supply and the wall outlet.
- Ensure the power supply's main switch is in the 'ON' (I) position.
- Verify the wall outlet is functional by plugging in another device.
- Confirm all internal power connectors (20+4 pin, 4+4 pin) are firmly seated.
- System Instability/Random Shutdowns:
- Ensure adequate ventilation. Overheating can cause instability.
- Check if the power supply is overloaded. Compare your system's power requirements with the power supply's specifications.
- Inspect for loose connections.
- Unusual Noises:
- A rattling or grinding noise may indicate a faulty fan. Disconnect power immediately and contact support.
- Do not attempt to repair the power supply yourself.
Specifications
The following are the technical specifications for the FSP460-60GLN Switching Power Supply:
| Feature | Specification |
|---|---|
| Model | FSP460-60GLN |
| Type | Industrial Level Switching Power Supply |
| Input Voltage | 100-240V~ |
| Input Current | 7.5-3.5A |
| Input Frequency | 50-60Hz |
| Output +5V | 0.0A (min) / 16.0A (max) |
| Output +3.3V | 0.0A (min) / 12.0A (max) |
| Output +12V | 0.0A (min) / 18.0A (max) |
| Output -12V | 0.3A |
| Output +5VSB | 2.5A |
| Combined Power (+3.3V & +5V) | 152W Max |
| Total Power | 460W |
| ASIN | B0DHSYMG3N |
| Manufacturer | Generic |
| Date First Available | September 23, 2024 |
Warranty and Support
For warranty information or technical support, please refer to the documentation provided by the seller or manufacturer at the time of purchase. You may also contact the seller directly through the platform where the product was acquired.
Note: As this is a generic product, specific warranty terms may vary. Always retain your proof of purchase.
