Introduction
This instruction manual provides detailed guidance for the setup, operation, and maintenance of your Stealth Cam 36MP Fusion Max Cellular Trail Camera. Please read this manual thoroughly before using the camera to ensure optimal performance and longevity.
Image: The Stealth Cam 36MP Fusion Max Cellular Trail Camera, shown with a 32GB SDHC UHS-I Memory Card and an All-In-One High Speed Card Reader, which are included in the bundle.
Product Overview
Key Features
- 36 Megapixel Resolution: Captures high-quality still images.
- Cellular Connectivity: Features two pre-installed SIM cards with Automatic Network Coverage for AT&T and Verizon, ensuring connection to the strongest network.
- 80-Foot Detection Range: Detects motion up to 80 feet away.
- Infrared Flash: Provides illumination for night captures without startling wildlife.
- 0.4-Second Trigger Speed: Rapid response to capture fast-moving subjects.
- Burst Mode: Captures one to six images per trigger.
- On-Demand Photo and Video Capture: Allows real-time capture and sending of media via the Command Pro app.
- Expanded Battery Capacity: Accommodates up to 16 AA batteries (not included) for extended field use.
- Versatile Power Options: Compatible with FieldMAX rechargeable lithium battery cartridges and solar panels.
- Durable Weatherproof Housing: Designed to withstand outdoor conditions.
Image: An infographic highlighting the camera's specifications including 36MP resolution, <0.4 sec trigger speed, 80 feet detection range, 720P 30 FPS video resolution, and infrared flash type.
Included Components
- Stealth Cam 36MP Fusion Max Cellular Trail Camera
- 32GB SDHC UHS-I Memory Card (100MB/s)
- All-In-One High Speed Card Reader
Image: A visual representation of the bundle contents, including the trail camera, a SanDisk Ultra 32GB SD card, and a Focus brand all-in-one high-speed card reader.
Setup
1. Battery Installation
The Fusion Max camera requires up to 16 AA batteries (not included). For best performance, use high-quality alkaline or lithium batteries. Ensure correct polarity when inserting batteries into the compartment.
- Open the camera's housing latch.
- Locate the battery compartment.
- Insert 16 AA batteries, observing the positive (+) and negative (-) indicators.
- Close the battery compartment securely.
Alternatively, the camera is compatible with Stealth Cam FieldMAX rechargeable lithium battery cartridges and solar panels for alternative power. Refer to the respective accessory manuals for their installation.
Image: Visual demonstration of the camera's power options, including the internal AA battery compartment and an external FieldMAX rechargeable lithium battery cartridge.
2. SIM Card Installation
The camera comes with two pre-installed SIM cards. No manual installation is required for these. The camera will automatically select the strongest AT&T or Verizon network signal.
3. SD Card Installation
A 32GB SDHC UHS-I Memory Card is included. Ensure the camera is powered off before inserting or removing the SD card.
- Locate the SD card slot on the camera.
- Insert the 32GB SD card with the label facing the correct direction until it clicks into place.
- To remove, gently push the card in until it springs out.
4. Mounting the Camera
The camera can be mounted using the integrated 1/4-inch threaded insert or a mounting strap (not included).
- Choose a stable location, such as a tree or post, that provides a clear view of the desired monitoring area.
- If using a strap, thread it through the slots on the back of the camera and secure it around the mounting surface.
- If using a tripod or other mounting hardware, attach it to the 1/4-inch threaded insert at the bottom of the camera.
- Adjust the camera's angle to optimize the detection range and field of view.
Image: A user demonstrating the setup of the Stealth Cam Fusion Max camera on a pole mount in a field, illustrating typical outdoor deployment.
5. Command Pro App Setup
The Command Pro app is essential for managing your Fusion Max camera, requesting on-demand media, and viewing images.
- Download the "Command Pro" app from your smartphone's app store (iOS or Android).
- Create an account or log in if you already have one.
- Follow the in-app instructions to add your Fusion Max camera. This typically involves scanning a QR code on the camera or manually entering its serial number.
- Once connected, you can configure camera settings, view images, and request on-demand captures.
Image: Screenshots illustrating the Command Pro app's capabilities, including viewing captured images, requesting on-demand photos and videos, and managing camera settings and sharing options.
Operating the Camera
Basic Operation
- Power On/Off: Use the power switch located inside the camera housing to turn the camera on or off.
- Mode Selection: The camera operates primarily in detection mode, capturing images or videos when motion is detected. Settings are configured via the Command Pro app.
Photo and Video Capture
The camera is designed to automatically capture media based on motion detection and your configured settings.
- When motion is detected within the 80-foot range, the camera will trigger within 0.4 seconds.
- Depending on settings, it will capture 36MP still images or 1080p video with audio.
- In burst mode, it can capture 1 to 6 images per trigger event.
- Captured media is saved to the installed SD card and transmitted via cellular network to your Command Pro app.
Image: Examples of images captured by the Fusion Max camera, showcasing its ability to capture clear photos of wildlife, including deer, with timestamp and temperature data.
Cellular Connectivity and On-Demand Features
The cellular function allows remote monitoring and control.
- Automatic Network Coverage: The camera continuously monitors AT&T and Verizon signal strength and connects to the strongest available network.
- On-Demand Capture: Through the Command Pro app, you can request the camera to take and send new photos or videos in real-time.
- Remote Settings Adjustment: Most camera settings, including photo/video mode, delay, and sensitivity, can be adjusted remotely via the app.
Maintenance
Cleaning
- Periodically wipe the camera lens and infrared flash array with a soft, lint-free cloth to ensure clear images.
- Clean the camera body with a damp cloth. Avoid abrasive cleaners or solvents.
- Ensure the housing latch and seals are free of debris to maintain weatherproof integrity.
Battery Replacement
- Monitor battery levels via the Command Pro app.
- Replace all batteries at the same time with fresh ones to ensure consistent power.
- If using rechargeable FieldMAX cartridges, recharge them as needed.
Firmware Updates
Stealth Cam may release firmware updates to improve camera performance or add new features. Check the Command Pro app or the Stealth Cam website for available updates and follow the provided instructions carefully.
Troubleshooting
Common Issues and Solutions
| Issue | Possible Cause | Solution |
|---|---|---|
| Camera not powering on | Dead or incorrectly installed batteries; power switch off. | Ensure batteries are fresh and installed with correct polarity. Check power switch position. |
| No images/videos captured | Full or faulty SD card; incorrect settings; no motion detected. | Format or replace SD card. Verify settings in Command Pro app. Ensure camera is aimed at an active area. |
| Poor image/video quality | Dirty lens; low light; subject too far. | Clean lens. Ensure adequate lighting or use infrared flash effectively. Position camera closer to subject. |
| No cellular signal/transmission | Poor network coverage; SIM card issue; data plan expired. | Relocate camera to an area with better signal. Check data plan status. Contact Stealth Cam support if SIM issue persists. |
| Command Pro app connectivity issues | Internet connectivity on phone; app version outdated; camera not registered. | Check phone's internet connection. Update app. Re-register camera if necessary. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | STC-FXWTX-K1 |
| Image Resolution | 36 Megapixels |
| Video Resolution | 1080p at 30 frames per second (MP4 format) |
| Detection Range | 80 feet |
| Trigger Speed | 0.4 seconds |
| Flash Type | Infrared |
| Connectivity | Cellular (AT&T and Verizon automatic network coverage) |
| Power Source | 16 AA batteries (not included), compatible with FieldMAX rechargeable lithium battery cartridges and solar panels |
| Memory Card Support | SDHC UHS-I (32GB card included) |
| Dimensions (L x W x H) | 9.1 x 9.1 x 9.1 inches |
| Weight | 9.43 pounds |
| Material | Plastic |
| Water Resistance Level | Water Resistant |
| Mounting Type | Wall Mount (via strap or 1/4-inch threaded insert) |
Warranty and Support
Warranty Information
For specific warranty details, please refer to the warranty card included with your product or visit the official Stealth Cam website. Typically, products are covered against defects in materials and workmanship for a specified period from the date of purchase.
Customer Support
If you encounter any issues not covered in this manual or require further assistance, please contact Stealth Cam customer support:
- Website: Visit the official Stealth Cam website for FAQs, support resources, and contact information.
- Phone: Refer to the product packaging or website for customer service phone numbers.
Please have your model number (STC-FXWTX-K1) and purchase date ready when contacting support.