ANWBROAD Watch Winder UJWW002E Instruction Manual

Introduction

This manual provides comprehensive instructions for the setup, operation, and maintenance of your ANWBROAD Watch Winder Model UJWW002E. This device is designed to keep your automatic watches wound and ready for use, while also offering additional storage for other timepieces and jewelry.

Product Features

• 4+6 Watch Capacity: Features 4 winding slots for automatic watches and 6 additional storage slots for other watches or jewelry.
• Super Quiet Motor: Operates at a sound level of only 5 decibels, ensuring minimal disturbance.
• Elegant Design: Piano paint finish with a wood grain pattern, complemented by an LED backlight.
• Anti-Magnetic Protection: Designed to protect watches from magnetic interference.
• 4 Rotation Modes: Multiple winding settings to suit various automatic watch requirements.
• USB Powered: Convenient charging via USB cable, compatible with various power devices.
• Lid-Activated Stop: Rotation automatically stops when the lid is opened.

Package Contents

• ANWBROAD Watch Winder UJWW002E
• USB Charging Cable
• Instruction Manual (this document)

Setup Instructions

1. Unpacking: Carefully remove the watch winder from its packaging. Inspect for any damage.
2. Power Connection: Connect the provided USB charging cable to the Type-C Power Input port located on the side of the winder. Connect the other end to a suitable USB power source (e.g., wall adapter, power bank, computer USB port).
   

   Image: Side panel with USB-C input and control switches.
3. Placing Watches:
   • For winding slots: Place your automatic watches onto the adjustable watch pillows. Ensure the watch is securely fitted. The pillows are designed to accommodate various watch sizes.
   • For storage slots: Place additional watches or jewelry into the 6 static storage compartments.
   

   Image: Watch winder with watches placed in winding and storage slots.

Operating Instructions

The ANWBROAD Watch Winder features independent controls for each winding rotor and the LED backlight. This allows for customized operation.

Control Switches:

• Power Switch (Left Toggle): Controls the power to the winding mechanisms.
• LED Switch (Right Toggle): Controls the internal LED backlight.
• Rotation Mode Knobs: Two independent rotary knobs, one for each pair of winding slots, allow selection of different rotation modes.

Image: Control panel with power and LED switches, and USB-C port.

Image: Rotary knobs for selecting rotation modes.

Rotation Modes:

Select the appropriate mode for your automatic watches using the rotary knobs. Each knob controls one pair of winding slots.

• Mode 1: Rotates clockwise for 2 minutes, then stops for 6 minutes. Repeats cycle.
• Mode 2: Rotates counter-clockwise for 2 minutes, then stops for 6 minutes. Repeats cycle.
• Mode 3: Rotates clockwise for 2 minutes, stops for 6 minutes; then rotates counter-clockwise for 2 minutes, stops for 6 minutes. Repeats cycle.
• Mode 4: Rotates clockwise for 5 minutes, then counter-clockwise for 5 minutes. This sequence runs for 3 hours, followed by a 9-hour stop. Repeats cycle.

Image: Visual representation of the four rotation modes.

Lid Sensor:

The winder is equipped with a safety feature that automatically stops rotation when the lid is opened. This prevents accidental contact with moving parts and allows for safe placement or removal of watches.

Maintenance

• Cleaning: Wipe the exterior with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Interior Care: Gently dust the interior with a soft brush or cloth.
• Watch Pillows: Ensure watch pillows are clean and free of debris to prevent scratching watches.
• Placement: Place the winder on a stable, level surface away from direct sunlight, extreme temperatures, and strong magnetic fields.

Troubleshooting

• Winder Not Rotating:
  • Ensure the power cable is securely connected.
  • Verify the power switch is in the "ON" position.
  • Check if the lid is fully closed, as rotation stops when the lid is open.
  • Confirm a rotation mode is selected on the rotary knob (not "OFF").
• LED Light Not Working:
  • Ensure the LED switch is in the "ON" position.
  • Check power connection.
• Excessive Noise:
  • Ensure the winder is on a stable, flat surface.
  • Verify watches are securely placed on pillows and not touching any internal surfaces.
  • The motor is designed to be quiet (below 5dB). If noise persists, contact customer support.
  

  Image: Illustration of the watch winder's quiet operation.

Specifications

Image: Product dimensions and watch pillow size.

Warranty and Support

The ANWBROAD Watch Winder comes with a limited warranty. For specific details regarding warranty coverage, please refer to the documentation included with your purchase or contact ANWBROAD customer service.

ANWBROAD provides 24-hour customer service via email. If you have any questions or require assistance during use, please contact us for a satisfactory solution.

For additional support or inquiries, please visit the official ANWBROAD store: ANWBROAD Store

Product Videos