1. Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Budora 5304532555 Ice Maker Assembly. Please read this manual thoroughly before attempting any installation or service to ensure safe and correct usage. This ice maker is designed as a replacement part for compatible Frigidaire refrigerator models.
2. What's in the Box
Upon unpacking, please verify that all components are present and undamaged:
- 1 x Ice Maker Assembly (Model 5304532555)
3. Compatibility
The Budora 5304532555 Ice Maker Assembly is compatible with various refrigerator models from brands including Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore. Please cross-reference your refrigerator's model number with the list below to confirm compatibility.
Cross-Reference Part Numbers:
- 5304532555
- AP7193288
- 5304523840
- 5304532194
- 5304525923
- 5304531891
- 5304532196
- 5304532554
Compatible Frigidaire Refrigerator Models:
- FFHI1835VS0
- FFHI1835VS1
- FFHI1835VS2
- FFHI1835VS3
- FFHI1835VS4
- FRSS2323AB0
- FRSS2323AB2
- FRSS2323AB5
- FRSS2323AB6
- FRSS2323AB7
- FRSS2323AD0
- FRSS2323AD2
- FRSS2323AD3
- FRSS2323AD5
- FRSS2323AS0
- FRSS2323AS2
- FRSS2323AS3
- FRSS2323AS4
- FRSS2323AS5
- FRSS2323AS7
- FRSS2323AS8
- FRSS2323AW0
- FRSS2323AW1
- FRSS2323AW4
- FRSS2323AW5
- FRSS2323AW7
- FRSS2333AS0
- FRSS2333AS5
- FRSS23L3AF0
- FRSS2623AB0
- FRSS2623AB1
- FRSS2623AB2
- FRSS2623AB4
- FRSS2623AB6
- FRSS2623AB8
- FRSS2623AD0
- FRSS2623AD2
- FRSS2623AD3
- FRSS2623AD6
- FRSS2623AD8
- FRSS2623AS0
- FRSS2623ASB
- FRSS2623ASC
- FRSS2623AW0
- FRSS2623AW1
- FRSS2623AW2
- FRSS2623AW3
- FRSS2623AW5
- FRSS2623AW6
- FRSS2623AW7
- FRSS2623AW8
- FRSS2633AS0
- FRSS2633AS4
- FRSS2633AS5
- FRSS26L3AB0
- FRSS26L3AF0
- FRSS26L3AF5
- FRSS26L3AF7
- FRSS26L3AW0
4. Setup and Installation
Safety First: Before beginning any installation, always disconnect power to your refrigerator to prevent electrical shock. It is recommended to have this part installed by a qualified technician.
- Preparation: Ensure the refrigerator is unplugged and the water supply line to the ice maker is shut off. Remove any existing ice maker components if you are replacing an old unit.
- Positioning: Carefully position the new ice maker assembly in the designated compartment within your freezer. Ensure all mounting points align.
- Electrical Connection: Connect the electrical harness from the ice maker to the corresponding receptacle in the refrigerator. Ensure the connection is secure.
- Water Line Connection: If applicable, ensure the water fill tube is correctly aligned with the ice maker's water inlet.
- Securing the Unit: Fasten the ice maker assembly using the appropriate screws or clips, ensuring it is stable and level.
- Final Checks: Once installed, restore the water supply and plug the refrigerator back into power. Allow several hours for the ice maker to cycle and produce ice.
Figure 1: Top-down view of the Budora 5304532555 Ice Maker Assembly, showing the ice mold and internal components.
Figure 2: Side view of the ice maker assembly, highlighting the electrical connector and internal mechanism.
Figure 3: Another top-down perspective of the ice maker, showing the ice tray and water fill area.
Figure 4: Close-up view of the electrical connector, crucial for proper power supply and function.
5. Operation
Once installed and connected, the ice maker will automatically begin its ice production cycle. The first batch of ice may take several hours to form. Discard the first few batches of ice to ensure cleanliness and proper functioning.
- Initial Start-up: After installation, allow 24 hours for the freezer to reach optimal temperature and for the ice maker to produce a full bin of ice.
- Ice Production: The ice maker will cycle automatically, filling with water, freezing, and then ejecting ice into the ice bin.
- Shut-off Arm: Most ice makers include a shut-off arm. When the ice bin is full, this arm will rise, temporarily stopping ice production until ice is removed.
6. Maintenance and Care
Regular maintenance helps ensure the longevity and efficient operation of your ice maker.
- Cleaning: Periodically clean the ice bin and the ice maker components with a mild soap and water solution. Rinse thoroughly and dry before reassembly. Do not use abrasive cleaners.
- Water Filter: If your refrigerator has a water filter, ensure it is replaced according to the manufacturer's recommendations to maintain water quality and prevent mineral buildup in the ice maker.
- Inspection: Occasionally inspect the water fill tube for any blockages or ice buildup.
7. Troubleshooting Common Issues
If your ice maker is not functioning as expected, consider the following common issues:
- No Ice Production:
- Ensure the refrigerator is plugged in and receiving power.
- Check if the water supply valve to the refrigerator is open.
- Verify the ice maker's shut-off arm is in the down (ice-making) position.
- Confirm the freezer temperature is set correctly (typically 0°F / -18°C).
- Small or Hollow Ice Cubes:
- Check water pressure to the refrigerator.
- Inspect the water fill tube for partial blockages.
- Replace the water filter if it is old or clogged.
- Ice Maker Leaking:
- Ensure the water fill tube is properly aligned with the ice maker's inlet.
- Check for cracks in the water line or ice maker components.
For persistent issues, contact a qualified appliance repair technician.
8. Product Specifications
| Feature | Detail |
|---|---|
| Brand | Budora |
| Model Number | PL-5304532555 |
| Item Model Number | PL-5304532555 |
| Product Dimensions | 14 x 6 x 4 inches |
| Item Weight | 1.59 Pounds |
| UPC | 810162811594 |
| Manufacturer | Budora |
| ASIN | B0DD85X949 |
9. Warranty and Support
This Budora Ice Maker Assembly comes with a One Year Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For warranty claims or technical support, please refer to the contact information provided by your retailer or the Budora official website.
Please retain your proof of purchase for warranty validation.
