1. Introduction
Thank you for choosing the Generic Kitchen Extractor Hood. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new appliance. Please read this manual thoroughly before use and retain it for future reference.
2. Safety Information
Always adhere to the following safety precautions to prevent injury or damage to the appliance.
- Ensure the power supply voltage matches the rating label on the hood.
- Do not operate the hood with wet hands.
- Regularly clean the grease filters to prevent fire hazards.
- Do not flambé under the range hood.
- Ensure adequate ventilation in the room when the range hood is used simultaneously with gas or other fuel-burning appliances.
- Disconnect the appliance from the power supply before cleaning or maintenance.
- Installation must be performed by a qualified technician in accordance with local regulations.
3. Product Overview
3.1 Key Features
- Hidden Convenient Switch: Pull-out design for fast and slow adjustment, maintaining aesthetic appeal.
- Simple and Intuitive Controls: Clear keyboard style buttons with a long service life.
- LED Lighting: Two 1.5W LED lights illuminate the cooking area for clear visibility.
- 3-Layer Metal Filter: Effectively removes grease and cooking odors, easily detachable for cleaning.
- Modern and Space-saving Design: Integrated, flush-fitting design for a neat kitchen appearance.
- Strong Suction: 14M3 / min airflow to effectively remove odors, steam, and grease while keeping noise low.
3.2 Components
The product typically includes the main extractor hood unit, 3-layer metal filters, and integrated LED lights.
Figure 1: Bottom view of the Kitchen Extractor Hood, showcasing the pull-out section with metal filters and integrated LED lights.
4. Setup and Installation
This extractor hood is designed for built-in installation within kitchen cabinetry. Professional installation is recommended.
4.1 Dimensions and Placement
Ensure your cabinet space accommodates the hood's dimensions for proper integration.
- Smoke machine size: 600mm (length) × 280mm (side width) × 40mm (height)
- Hoarding size: 510mm (length) × 285mm (side width) × 220mm (height)
Figure 2: Product dimensions for installation planning.
Figure 3: Example of the built-in three-dimensional design integrated into kitchen cabinetry.
4.2 Electrical Connection
The hood requires a 220V~50Hz power supply. The power cord is 1.5m long. Ensure the electrical connection is made by a qualified electrician.
4.3 Ventilation Options
This model supports an inner loop (recirculating) operation, which means it does not require an external smoke pipe. It absorbs oil fume through the oil screen filter and activated carbon, then discharges purified air back into the kitchen.
Figure 4: Internal circulation mechanism with oil filter and activated carbon.
Figure 5: Inner loop operation, suitable for simple steaming and cooking, frying steak, bread, etc. Not recommended for heavy stir-frying.
5. Operating Instructions
5.1 Powering On/Off and Speed Control
To operate the hood, gently pull out the hidden front panel. This action will typically activate the fan and lights. The control buttons for fan speed (fast/slow) are located on the panel. Press the desired speed button to adjust the suction power.
Figure 6: Pull-out operation and air intake.
5.2 LED Lights
The hood is equipped with two 1.5W LED lights. A dedicated button on the control panel allows you to turn the lights on or off independently of the fan operation.
6. Maintenance and Cleaning
Regular cleaning ensures optimal performance and extends the lifespan of your extractor hood.
6.1 Cleaning the Metal Filters
The 3-layer metal filters should be cleaned regularly, depending on usage. They can be easily detached for cleaning.
- Ensure the hood is turned off and disconnected from the power supply.
- Locate the release latches on the filters and gently pull them down to remove.
- Clean the filters using warm soapy water or a dishwasher. For stubborn grease, a degreasing agent may be used.
- Rinse thoroughly and allow to dry completely before re-installing.
Figure 7: Cleaning the metal filter.
6.2 Cleaning the Hood Surface
Wipe the stainless steel surfaces with a soft cloth dampened with mild detergent. Avoid abrasive cleaners or scouring pads, as they can scratch the finish.
7. Troubleshooting
If you encounter issues with your extractor hood, refer to the following common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not operate | No power supply Power cord disconnected | Check power outlet and circuit breaker Ensure power cord is securely plugged in |
| Weak suction power | Grease filters are clogged Obstruction in air intake/outlet | Clean the metal filters Check for any blockages |
| Excessive noise | Loose components Fan motor issue | Check if filters are properly installed Contact qualified service personnel |
| LED lights not working | Light bulb faulty Electrical connection issue | Replace LED bulb (if replaceable) Contact qualified service personnel |
If the problem persists after attempting these solutions, please contact qualified service personnel.
8. Specifications
| Specification | Detail |
|---|---|
| Product Name | Stainless Steel Range Hood |
| Model Number | Ah95ZkONuhGRIkqM |
| Product Material | Stainless Steel |
| Smoke Machine Size (L×W×H) | 600mm × 280mm × 40mm |
| Hoarding Size (L×W×H) | 510mm × 285mm × 220mm |
| Power Cord Length | 1.5m |
| Power Supply | 220V~50Hz |
| Input Power | 200W |
| Product Wind Pressure | 280Pa |
| Air Volume | 14M3 / min |
| LED Light | 1.5W × 2 |
| Filter Type | Mesh (3-layer metal) |
| Mounting Type | Built-In Mount |
| Special Feature | Easy To Clean |
| Country of Origin | China |
9. Warranty and Support
Specific warranty details for this product are not provided in this manual. For warranty claims, technical support, or service inquiries, please contact the retailer or manufacturer directly using the contact information provided at the time of purchase.