Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your new Euplokeer Hood Strut Lift Supports. Designed for specific Toyota models, these supports ensure smooth and effortless opening and closing of your vehicle's hood, enhancing convenience and safety.
Product Compatibility
The Euplokeer Hood Strut Lift Supports are compatible with the following vehicle models:
- Toyota Avalon: 2013-2018
- Toyota Camry: 2012-2017
These supports are designed to replace original equipment (OE) part numbers including, but not limited to: 6757, 241421, 5344006090, 5344006091, 53440-06091, 5344006100, 5344006110, 5344006120, 5344006130, 5344006140, 5345006080, 53450-06080, 5345006081, 53450-06081, 5345006090, 5345006100, 5345006110, 5345006120, 5345006130. To ensure proper fitment, it is crucial to compare the cylinder part numbers of your original gas struts with the compatible numbers listed. Additionally, measure the extended length of your existing gas shock lift and compare it with the product's specifications.
Figure 1: Product Compatibility and Dimensions. This image illustrates the compatible vehicle models (Toyota Camry 2012-2017, Toyota Avalon 2013-2018) and lists key OEM part numbers. It also shows the extended length of the strut, which is 26.40 inches.
Product Features
The Euplokeer Hood Strut Lift Supports incorporate advanced design and materials for enhanced performance and durability:
- Quench-Polish-Quench (QPQ) Technology: This surface treatment greatly improves wear resistance and provides excellent corrosion resistance, ensuring a longer lifespan for the struts.
Figure 2: Quench-Polish-Quench Technology. This close-up highlights the advanced surface treatment applied to the strut rod, which enhances its durability and resistance to wear and corrosion.
- 10mm PA66 Ball Socket: The ball socket is made from high-strength and stiff PA66 material, ensuring precise adaptation to OEM specifications for a secure fit.
Figure 3: 10mm PA66 Ball Socket. This image focuses on the ball socket component, emphasizing its construction from PA66 for strength and stiffness, ensuring a precise fit.
- Highly Hermetic Structural Design: Engineered for a service life of 50,000 cycles, this design ensures excellent sealing performance without air leakage, maintaining consistent pressure and function.
Figure 4: Highly Hermetic Structural Design. This diagram provides an internal view of the strut, showcasing its sealed design and various components that contribute to its long service life and prevention of air leakage.
- Seamless Thickened Steel Pipe: Constructed from heavy-duty steel, the pipe offers excellent stress tolerance and durability.
- Double-layer Oil Seal: Provides superior sealing performance to prevent oil leakage.
Setup and Installation
Installation of the Euplokeer Hood Strut Lift Supports is designed to be straightforward. This listing includes two (2) gas shocks, one for each side of the hood.
Required Tools:
- Flathead screwdriver (or similar prying tool)
- Assistance from another person (recommended for safety)
Installation Steps:
- Secure the Hood: Before beginning, ensure the vehicle's hood is securely propped open using a temporary support or with the assistance of another person. This prevents accidental closure during the installation process.
- Remove Old Struts: Using a flathead screwdriver, carefully pry off the clips securing the old hood struts at both the upper and lower mounting points. Once the clips are disengaged, the old strut can be removed.
- Install New Struts: Align the new Euplokeer hood strut with the mounting points. Press the ball sockets onto the ball studs until they click into place. Ensure both ends are securely fastened.
- Repeat for Second Strut: Follow the same procedure for the second hood strut.
- Test Functionality: Once both new struts are installed, carefully lower and raise the hood to confirm smooth operation and secure support.
Installation typically takes less than 10 minutes.
Figure 5: Front Hood Lift Support in Use. This image shows a hood lift support installed on a vehicle, demonstrating its function in holding the hood open for access to the engine bay.
Operating Instructions
Once installed, the Euplokeer Hood Strut Lift Supports operate automatically. When you lift the hood, the gas shocks will extend to hold it open securely. To close the hood, gently pull it down; the struts will compress smoothly.
These supports are designed to provide an effortless opening and closing experience, freeing your hands for other tasks while working under the hood.
Maintenance
Euplokeer Hood Strut Lift Supports are designed for long-lasting performance with minimal maintenance. To ensure optimal function and longevity:
- Keep Clean: Periodically wipe down the strut rods with a clean, damp cloth to remove dirt and debris. Avoid using harsh chemicals or abrasive materials.
- Inspect for Damage: Regularly check the struts for any signs of damage, such as bends, dents, or leaks. Also, inspect the mounting points and clips for wear or looseness.
- Avoid Lubricants: Do not apply oil or grease to the strut rods, as this can attract dirt and potentially damage the seals.
Troubleshooting
If you encounter issues with your hood strut lift supports, consider the following:
- Hood Not Staying Up: If the hood does not stay open or sags, the struts may be worn out or incorrect for your vehicle.
- Verify that the installed struts match the correct OEM part numbers and extended length for your specific vehicle model.
- Ensure both struts are properly installed and securely clipped into their mounting points.
- Difficulty Opening/Closing: If the hood is unusually stiff to open or close, the struts might be too strong or misaligned.
- Re-check the compatibility and ensure you have the correct model for your vehicle.
- Inspect the mounting points for any obstructions or misalignment.
For further assistance, please refer to the Warranty and Support section.
Specifications
| Attribute | Detail |
|---|---|
| Brand | Euplokeer |
| Model Number | 53440-06091 |
| Manufacturer Part Number | 5344006090 |
| Item Weight | 1.59 pounds (for the pair) |
| Package Dimensions | 17.83 x 2.32 x 1.18 inches |
| Position | Front (Hood) |
| Extended Length | 26.4 Inches |
| Color | Black |
| Quantity Included | 2 Gas Shocks |
Warranty and Support
Euplokeer stands behind the quality of its products. Your Hood Strut Lift Supports come with the following support:
- Product Exchange Service: Enjoy a 15-month product exchange service from the date of purchase.
- Customer Support: For any inquiries, technical assistance, or warranty claims, please contact Euplokeer customer service. We offer 24-hour email response to address your concerns promptly.
Please retain your proof of purchase for warranty claims.