Introduction
Thank you for choosing the Seang Electric Standing Desk. This desk is designed to provide an ergonomic workspace, allowing you to easily switch between sitting and standing positions throughout your day. This manual contains important information regarding the safe assembly, operation, and maintenance of your new standing desk. Please read it thoroughly before use and retain it for future reference.
Safety Information
- Weight Limit: Do not exceed the maximum weight capacity of 154 lbs (70 kg). Overloading the desk can cause instability and damage.
- Assembly: Assemble the desk strictly according to the provided instructions. Ensure all screws and fasteners are securely tightened before use.
- Clearance: Ensure there are no obstructions above or below the desk when adjusting its height to prevent damage or injury.
- Power: Use only the provided power adapter. Keep the power cord away from heat sources and sharp edges. Do not operate the desk with a damaged cord or plug.
- Children and Pets: Keep children and pets away from the desk during operation to prevent accidents.
- Stability: Place the desk on a level surface. Do not sit or stand on the desk.
Image: The desk is designed to support up to 154 lbs. Do not exceed this weight limit.
Package Contents
Please verify that all components are present before beginning assembly. If any parts are missing or damaged, please contact customer support.
- Desktop Surface
- Desk Legs (2)
- Foot Pads (2)
- Electric Motor and Control Box
- Control Panel with LED Display
- Power Adapter and Cable
- Headphone Hooks (2)
- Assembly Hardware (screws, bolts, etc.)
- L-shaped Mounting Tools
- Instruction Manual
Assembly Instructions
The Seang Electric Standing Desk is designed for straightforward assembly. A detailed installation manual is included in the package, along with precise pre-drilled holes and L-shaped mounting tools to facilitate the process.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface to prevent scratches.
- Attach Feet to Legs: Secure the foot pads to the bottom of each desk leg using the provided screws.
- Assemble Frame: Connect the desk legs to the crossbar and motor assembly according to the diagrams in the included manual.
- Mount Desktop: Carefully place the desktop onto the assembled frame, aligning the pre-drilled holes. Secure the desktop to the frame using the provided screws and L-shaped tools.
- Install Control Panel and Hooks: Attach the control panel to the underside of the desktop in the designated area. Install the headphone hooks as desired.
- Connect Wiring: Connect the motor and control panel cables to the control box, then connect the power adapter. Ensure all connections are secure.
Image: Follow the clear installation instructions and use the provided tools for easy assembly.
Operating Instructions
Your Seang Electric Standing Desk features an intuitive control panel for easy height adjustments and memory presets.
Control Panel Overview
Image: The multi-function intelligent keypad features an LED display, up/down buttons, and two memory buttons.
- LED Display: Shows the current desk height in inches.
- Up/Down Buttons (▲ / ▼): Press and hold to raise or lower the desk height. Release to stop.
- Memory Buttons (1, 2): Used to save and recall preferred height settings.
Height Adjustment
The desk's height can be adjusted from 28.3 inches to 46.5 inches. The powerful motor ensures a smooth and quiet lifting process (approximately 45dB).
- Press and hold the ▲ (Up) button to raise the desk.
- Press and hold the ▼ (Down) button to lower the desk.
- Release the button when the desired height is reached.
Image: The desk offers an adjustable height range from 28.3 inches to 46.5 inches.
Setting Memory Presets
You can save two preferred height settings for quick access.
- Adjust the desk to your desired height using the Up/Down buttons.
- Press and hold one of the Memory Buttons (1 or 2) until the LED display flashes or beeps, indicating the height has been saved.
- To recall a saved height, simply press the corresponding Memory Button (1 or 2). The desk will automatically move to the saved position.
Image: The desk operates with an ultra-quiet design, producing approximately 45dB during height adjustments.
Maintenance
To ensure the longevity and proper functioning of your Seang Electric Standing Desk, follow these simple maintenance guidelines:
- Cleaning: Wipe the desk surface and frame with a dry, soft cloth. Avoid using abrasive cleaners or harsh chemicals that could damage the finish.
- Inspections: Periodically check all screws and connections to ensure they remain tight. Retighten if necessary.
- Cable Management: Keep cables organized and free from entanglement to prevent damage to the motor or control panel wiring.
- Avoid Liquids: Do not spill liquids on the control panel or motor components. If a spill occurs, immediately unplug the desk and allow it to dry completely before reconnecting power.
Troubleshooting
If you encounter any issues with your Seang Electric Standing Desk, please refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Desk does not move | Power cable disconnected; Motor overload; Control panel issue | Check power connections; Unplug for 10 minutes then replug; Contact support if issue persists. |
| Uneven height adjustment | Obstruction; Unbalanced load | Remove any obstructions; Redistribute weight evenly on the desktop. |
| Desk stops mid-movement | Overload protection activated | Reduce weight on the desk; Wait 20 minutes for the motor to cool down before attempting adjustment again. |
| Memory presets not working | Presets not saved correctly | Re-save the desired height settings following the instructions in the 'Operating Instructions' section. |
If these solutions do not resolve the issue, please contact Seang customer support for further assistance.
Specifications
Detailed specifications for the Seang Electric Standing Desk:
Image: Key dimensions and maximum load capacity of the desk.
- Model Name: JZQC
- Model Number: S
- Desk Design: Standing Desk
- Product Dimensions (Desktop): 40 inches (Width) x 24 inches (Depth)
- Height Adjustment Range: 28.3 inches (Minimum) to 46.5 inches (Maximum)
- Maximum Weight Capacity: 154 lbs (70 kg)
- Lifting Mechanism: Electric
- Motor Noise Level: Approximately 45dB
- Top Material Type: Wood
- Base Material: Metal (Alloy Steel)
- Color: White Top, White Base
- Assembly Required: Yes (Includes all assembly tools)
- Recommended Number of People for Assembly: 1
- Product Care: Wipe with Dry Cloth
Warranty and Support
The Seang Electric Standing Desk comes with a limited warranty. Please refer to the warranty card included in your package for specific terms and conditions.
For any questions, technical assistance, or warranty claims, Seang offers 24/7 customer support. Please contact us via:
- Email: support@seang.com
- Website: www.seang.com/support
Please have your model number (JZQC, Model S) and purchase date ready when contacting support.