Introduction
The Ailgely M-VAVE WP-10 is a compact and professional 2.4GHz wireless earphone monitor transmission system designed for musicians, performers, and audio enthusiasts. It provides lossless digital audio transmission with low latency, ensuring a clear and reliable monitoring experience. This system includes a rechargeable transmitter and receiver, offering flexibility and convenience for various audio setups.
Product Overview
Familiarize yourself with the components and controls of your M-VAVE WP-10 system.
Figure 1: Detailed view of the Transmitter and Receiver components.
Transmitter Components:
- Power Switch: Turns the unit ON/OFF.
- Mono/Stereo Switch: Toggles between mono and stereo output modes.
- Clamp: For attaching the transmitter to clothing or equipment.
- Pairing Button: Initiates the pairing process with the receiver.
- Pairing Status LED: Indicates the pairing status.
- Power Status LED: Indicates power and battery status.
- Mobile Phone/Musical Instrument Input: 3.5mm input jack for audio source.
- Charging Port: USB-C port for charging the internal battery.
Receiver Components:
- Power Switch: Turns the unit ON/OFF.
- Mono/Stereo Switch: Toggles between mono and stereo output modes.
- Clamp: For attaching the receiver to clothing or equipment.
- Pairing Button: Initiates the pairing process with the transmitter.
- Pairing Status LED: Indicates the pairing status.
- Power Status LED: Indicates power and battery status.
- Headphone/Speaker Output: 3.5mm output jack for headphones or speakers.
- Volume Up Button: Increases the output volume.
- Volume Down Button: Decreases the output volume.
- Charging Port: USB-C port for charging the internal battery.
Setup
1. Charging the Devices
Before first use, fully charge both the transmitter and receiver. Use the included USB charging cable to connect each unit to a USB power adapter (not included) or a computer USB port. The Power Status LED will indicate charging status.
- Transmitter Battery Capacity: 780mAh
- Receiver Battery Capacity: 550mAh
2. Connecting Audio Sources and Outputs
Figure 2: Connecting the Transmitter to an audio source and the Receiver to earphones.
- Connect your audio source (e.g., mobile phone, musical instrument, mixer output) to the Mobile Phone/Musical Instrument Input (7) on the Transmitter using an appropriate audio cable.
- Connect your headphones or speakers to the Headphone/Speaker Output (7) on the Receiver.
3. Pairing the Transmitter and Receiver
The units are typically pre-paired from the factory. If they do not connect automatically, follow these steps:
- Turn ON both the Transmitter and Receiver using their respective Power Switches (1).
- Press and hold the Pairing Button (4) on both the Transmitter and Receiver simultaneously for a few seconds until their Pairing Status LEDs (5) start blinking rapidly.
- Release the buttons. The LEDs will turn solid when a successful connection is established.
Operating Instructions
Mono/Stereo Mode Selection
The M-VAVE WP-10 supports both mono and stereo audio transmission. Use the Mono/Stereo Switch (2) on both the Transmitter and Receiver to select the desired mode. Ensure both units are set to the same mode for optimal performance.
Volume Control (Receiver)
Adjust the output volume on the Receiver using the Volume Up Button (8) and Volume Down Button (9). Start with a low volume and gradually increase it to a comfortable listening level.
Multi-Receiver Support
Figure 3: One Transmitter can support multiple Receivers simultaneously.
The system allows one transmitter to send signals to up to 5 receivers simultaneously. To connect additional receivers, simply pair them with the active transmitter following the pairing instructions in the Setup section.
Using as a Collar-Clip Microphone/Pocket Transmitter
The transmitter can function as a collar-clip wireless microphone or a pocket-strapped transmitter when connected to an external microphone (not included) via its input jack.
Maintenance
- Keep the devices clean by wiping them with a soft, dry cloth.
- Avoid exposing the units to extreme temperatures, humidity, or direct sunlight.
- Do not disassemble the devices. Repairs should only be performed by qualified personnel.
- Recharge the batteries regularly, even if the devices are not in frequent use, to maintain battery health.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound or intermittent sound. |
|
|
| Short transmission range. |
|
|
| LED indicators not working. |
|
|
Specifications
| Feature | Detail |
|---|---|
| Model | WP-10 |
| Sample Rate | 24bit / 48KHz lossless digital transmission |
| Wireless Band | 2.4GHz |
| Delay | <12ms |
| Range | 30 meters outdoor or 15 meters wall distance |
| Transmitter Battery Capacity | 780mAh Lithium-Ion |
| Receiver Battery Capacity | 550mAh Lithium-Ion |
| Charging | USB charging cable |
| Signal-to-noise Ratio (SNR) | -98dB |
| Dynamic Range | >105dB |
| Frequency Response | 20 to 20KHz, +1dB / -3dB |
| Material | Acrylonitrile Butadiene Styrene (ABS) |
| Color | Black |
| Item Size | 60 * 45 * 20mm / 2.36 * 1.77 * 0.79in |
| Item Weight | 100g / 3.53oz |
Important Information
Please observe the following warnings for safe and optimal use:
- Avoid using the device near other 2.4GHz devices to prevent potential signal interference.
- Keep the battery away from extreme temperatures and high humidity.
- Dispose of batteries according to local regulations. Do not dispose of batteries in fire or with household waste.
- Do not attempt to modify or repair the device yourself. Refer to qualified service personnel.
Support
For technical support, warranty inquiries, or service, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific contact details.
Manufacturer: Ailgely
Seller: BevyInfor (as per Amazon Buy Box information)
For protection plans, please refer to the options available at the time of purchase, such as the 2-Year or 3-Year Protection Plans.