LyxJam 2x2 USB Audio Interface Studio Bundle User Manual

Introduction

This manual provides detailed instructions for the LyxJam 2x2 USB Audio Interface Studio Bundle. This comprehensive kit is designed to establish a computer-based recording studio, offering a 24-bit/192 kHz 2-channel USB interface, an LP professional condenser microphone, closed-back monitoring headphones, Mackie CR3.5 Creative Reference powered studio monitors, necessary cabling, a microphone stand, and a creative software suite. It is compatible with Mac and Windows computers for recording, mixing, and streaming studio-quality audio.

What's in the Box

Verify that all components listed below are included in your package:

• LyxJam 2x2 USB Audio Interface (24-bit/192 kHz, dual combo inputs)
• LP Professional Studio Condenser Microphone (matte black)
• Shock Mount for LP Microphone
• Pop Filter with Gooseneck & Clamp
• XLR Microphone Cable
• Closed-Back Recording Headphones
• Pair of Mackie CR3.5 3.5" Powered Multimedia Studio Monitors
• TRS Cables for Connecting Interface to Monitors
• Additional Audio Cables
• Adjustable Boom Microphone Stand
• USB 2.0 Cable for Interface
• Waveform OEM DAW & Creative Studio Software Bundle (download instructions included)

Setup

Follow these steps to set up your LyxJam Studio Bundle.

1. Connect the Audio Interface to your Computer

Use the provided USB 2.0 cable to connect the LyxJam 2x2 USB Audio Interface to an available USB port on your Mac or Windows computer. The interface is bus-powered, so no external power adapter is needed.

Figure 1: Rear panel connections of the LyxJam 2x2 USB Audio Interface. The USB 2.0 port connects to a computer for power and data transfer. Main outputs connect to studio monitors.

2. Install Software

Refer to the included instructions for downloading and installing the Waveform OEM DAW and any additional creative software. Ensure your computer's operating system is up to date for optimal compatibility.

3. Connect the Microphone

Assemble the LP Professional Studio Condenser Microphone with the shock mount and attach it to the adjustable boom microphone stand. Use the XLR microphone cable to connect the microphone to either CH1 or CH2 combo input on the front of the audio interface.

Figure 2: LP Condenser Microphone assembled with its shock mount and pop filter on a stand.

4. Connect Headphones

Plug the closed-back recording headphones into the 1/4" PHONES output jack on the front panel of the audio interface.

Figure 3: Front panel of the LyxJam 2x2 USB Audio Interface. Inputs for microphone and instrument are visible, along with the headphone output.

5. Connect Studio Monitors

Use the provided TRS cables to connect the MAIN OUTPUTS (Right and Left) on the rear of the audio interface to the corresponding inputs on the Mackie CR3.5 powered studio monitors. Ensure the monitors are connected to a power source and turned on.

Figure 4: Overview of the complete LyxJam Studio Bundle setup, showing all components interconnected.

Operating Instructions

This section details the operation of your LyxJam Studio Bundle components.

1. Audio Interface Controls

• Gain Knobs (CH1/CH2): Adjust the input level for connected microphones or instruments. Observe the PEAK indicators; they should light up only occasionally during the loudest parts of your signal to avoid clipping.
• Hi-Z Switch: Engage this switch for direct connection of high-impedance instruments like electric guitars or basses.
• +48V Phantom Power: Press this button to supply +48V phantom power to condenser microphones (like the included LP microphone). Ensure this is off when using dynamic microphones or if your condenser microphone has its own power supply.
• Direct/DAW Monitoring: Toggle between Direct monitoring (zero-latency monitoring of your input signal) and DAW monitoring (monitoring the signal processed by your computer software).
• Mono/Stereo Switch: Select Mono for a summed mono signal or Stereo for separate left/right channels when monitoring.
• Main Out Knob: Controls the overall output volume to your studio monitors.
• Phones Knob: Adjusts the volume for the connected headphones.

2. Microphone Usage

The LP Professional Studio Condenser Microphone is designed for clear vocal and instrument capture. Ensure +48V phantom power is enabled on the interface. Position the pop filter between the microphone and the sound source to minimize plosive sounds (P, B, T). Adjust the microphone's position relative to the sound source to achieve the desired tone and minimize room reflections.

3. Studio Monitor Operation

The Mackie CR3.5 monitors provide accurate sound reproduction. Use the front-panel tone knob to adjust the sound character from a flat studio reference to an enhanced listening experience. The location switch optimizes response for desktop or bookshelf placement. Adjust the volume using the knob on the active monitor.

4. Software Integration (Waveform OEM)

Waveform OEM is a digital audio workstation (DAW) included with your bundle. It allows you to record multiple tracks, arrange songs, design podcasts, apply virtual instruments, amp simulations, and studio-grade effects. Consult the Waveform OEM documentation for detailed software operation.

Figure 5: Waveform OEM Digital Audio Workstation interface, showing track arrangements and editing tools.

Maintenance

Proper maintenance ensures the longevity and optimal performance of your studio bundle.

• Cleaning: Use a soft, dry cloth to clean all components. Avoid abrasive cleaners or solvents. For the microphone, gently clean the grille with a soft brush if necessary.
• Storage: When not in use, store components in a clean, dry environment away from extreme temperatures and humidity.
• Cable Management: Keep cables organized and avoid sharp bends or kinks to prevent damage.
• Software Updates: Regularly check for and install updates for your operating system and Waveform OEM software to ensure compatibility and access to new features.

Troubleshooting

If you encounter issues, refer to the following common problems and solutions.

• No Sound Output:
  • Check all cable connections (USB, XLR, TRS, headphones).
  • Ensure the audio interface is selected as the input/output device in your computer's sound settings and within your DAW (Waveform OEM).
  • Verify that the Main Out and Phones volume knobs on the interface are turned up.
  • Confirm that the Mackie CR3.5 monitors are powered on and their volume is adjusted.
• Microphone Not Working:
  • Ensure the XLR cable is securely connected to both the microphone and the interface.
  • Activate the +48V phantom power switch on the interface for the LP condenser microphone.
  • Adjust the input Gain knob for the microphone channel.
  • Check if the microphone is enabled and selected as an input in your DAW.
• Distorted Audio:
  • Reduce the input Gain knob on the interface if the PEAK indicator lights up frequently.
  • Check the output levels in your DAW and on the interface.
  • Ensure your computer's audio drivers are correctly installed and up to date.
• Latency (Delay in Monitoring):
  • Use the Direct Monitoring feature on the audio interface to hear your input signal with zero latency.
  • In your DAW, reduce the buffer size in the audio settings (this may increase CPU load).

Specifications

Warranty and Support

The LyxJam 2x2 USB Audio Interface Studio Bundle comes with a 1-year warranty. For technical support, warranty claims, or further assistance, please refer to the contact information provided with your product packaging or visit the official LyxJam website. Please have your product model and purchase date available when contacting support.