FTYUERT GEPRC Naked GoPro Hero 8 Case with BEC Board Instruction Manual

1. Introduction

This instruction manual provides comprehensive guidance for the installation, operation, and maintenance of the FTYUERT GEPRC Naked GoPro Hero 8 Case with BEC Board. This product is designed to enhance the functionality and protection of your Naked GoPro Hero 8 camera when used with compatible GEPRC quadcopters.

Please read this manual thoroughly before attempting installation or operation to ensure proper usage and to prevent damage to the product or your equipment.

2. Safety Information

• Always disconnect power from your drone before installing or removing the case and BEC board.
• Ensure all connections are secure and correctly polarized to avoid electrical damage.
• Handle the Naked GoPro Hero 8 camera with care, as it is delicate.
• Do not expose the BEC board to moisture or extreme temperatures.
• Verify compatibility with your specific GEPRC quadcopter model before installation.

3. Package Contents

Verify that all items listed below are present in your package:

• GEPRC Naked GoPro Hero 8 Case (ABS material)
• BEC Board (2S-6S input, 5V@2A output)
• ND16 Filter
• Mounting Base
• GH1.25-3P BEC Connector Cable
• GH1.25-3P Control Cable

4. Setup and Installation

Follow these steps carefully to install the GEPRC Naked GoPro Hero 8 Case and BEC Board onto your drone.

4.1 Installing the Naked GoPro Hero 8 into the Case

1. Gently insert your Naked GoPro Hero 8 camera into the GEPRC case. Ensure it fits snugly and securely. The case is made of durable ABS material and features UV protection for the camera lens.
2. Attach the provided ND16 filter to the camera lens if desired. The ND16 filter helps reduce light input without altering color, useful in bright conditions.

Image Placeholder: Naked GoPro Hero 8 being inserted into the GEPRC case.

This image would show the process of carefully placing the Naked GoPro Hero 8 camera module into the protective ABS case, highlighting the secure fit and lens area.

4.2 Connecting the BEC Board

1. Connect the BEC board to the Naked GoPro Hero 8 motherboard. The BEC board is specifically designed for the GoPro Hero 8 motherboard and provides a stable 5V@2A output.
2. Connect the GH1.25-3P BEC connector cable from the BEC board to your drone's power source (2S-6S input). Ensure correct polarity.

Image Placeholder: BEC board connected to GoPro Hero 8 motherboard and power source.

This image would illustrate the BEC board's connection points to the GoPro Hero 8 and the drone's flight controller or power distribution board, emphasizing the GH1.25-3P connector.

4.3 Mounting the Case to the Drone

1. Attach the mounting base to your GEPRC quadcopter. The installation spacing of the base is 24.5mm, making it compatible with various GEPRC series such as CineLog, Crocodile Baby, Rocket, and Crown.
2. Secure the assembled case with the Naked GoPro Hero 8 and BEC board onto the mounting base. The case features a dedicated mounting seat for easy installation.

Image Placeholder: Mounted GEPRC Naked GoPro Hero 8 case on a drone frame.

This image would show the complete assembly of the case and camera securely mounted onto a compatible GEPRC drone frame, demonstrating the 24.5mm mounting base.

4.4 Connecting the Control Cable

Connect the GH1.25-3P control cable from the BEC board to your drone's Flight Controller (FC). This connection enables remote control of the camera functions via the FC.

Image Placeholder: Control cable connection from BEC board to Flight Controller.

This image would detail the connection of the GH1.25-3P control cable between the BEC board and a designated port on the drone's flight controller, indicating the path for remote camera control.

5. Operating Instructions

Once installed, the Naked GoPro Hero 8 camera, powered by the BEC board, can be operated through your drone's flight controller (FC) if the control cable is connected. Refer to your FC's documentation for specific commands and configuration for camera control.

• Power On/Off: The camera will power on with the drone's main power.
• Recording: Use your FC's configured switch or command to start and stop video recording.
• Settings: Any camera settings adjustments typically need to be done before flight, as the Naked GoPro Hero 8 lacks external controls.

Video Placeholder: Demonstration of remote camera control via drone's flight controller.

This video would show a drone pilot using their remote control to activate recording on the Naked GoPro Hero 8 camera, demonstrating the functionality of the control cable connection.

6. Maintenance

• Cleaning: Use a soft, dry cloth to clean the case and ND16 filter. Avoid abrasive materials or harsh chemicals.
• Inspection: Regularly inspect the case for cracks or damage, especially after hard landings. Check all cable connections for wear or looseness.
• Storage: Store the product in a cool, dry place away from direct sunlight when not in use.

7. Troubleshooting

• Camera Not Powering On:
  • Check BEC board power input (2S-6S) from the drone.
  • Verify BEC output (5V@2A) to the GoPro motherboard.
  • Ensure all GH1.25-3P connectors are securely seated and correctly polarized.
• No Remote Camera Control:
  • Confirm the GH1.25-3P control cable is properly connected between the BEC board and the FC.
  • Check your FC's firmware and configuration for camera control settings.
  • Ensure the GoPro Hero 8 is functioning correctly independently.
• Poor Image Quality:
  • Clean the ND16 filter and GoPro lens.
  • Ensure the ND16 filter is correctly installed.
  • Check for any damage to the camera lens or case.

8. Specifications

9. Warranty and Support

FTYUERT products are manufactured to high-quality standards. For warranty information and technical support, please refer to the seller's return policy or contact the retailer where the product was purchased. Keep your proof of purchase for any warranty claims.

For further assistance, please visit the official FTYUERT website or contact their customer service department.