Breville BCA600BSS

Breville InFizz Aqua Sparkling Water Maker (BCA600BSS) Instruction Manual

Model: BCA600BSS

Introduction

This manual provides detailed instructions for the safe and efficient operation, setup, and maintenance of your Breville InFizz Aqua Sparkling Water Maker, Model BCA600BSS. Please read all instructions thoroughly before first use and retain this manual for future reference.

Breville InFizz Aqua Sparkling Water Maker in brushed stainless steel

Image: The Breville InFizz Aqua Sparkling Water Maker, featuring a sleek brushed stainless steel design with a clear water bottle attached.

Important Safety Information

Always follow basic safety precautions when using kitchen appliances, especially those involving pressurized gas, to reduce the risk of injury. Improper use of this appliance can result in injury.

  • Read all instructions before operating the appliance.
  • Do not place the appliance on or near a hot gas or electric burner, or in a heated oven.
  • Ensure the appliance is placed on a stable, flat, heat-resistant surface.
  • Only use water in the carbonating bottle. Do not carbonate any other liquids.
  • Do not carbonate an empty bottle.
  • Do not remove the carbonating bottle during carbonation.
  • Only use Breville approved carbonating bottles with this appliance.
  • Only use standard screw-type 60L CO2 canisters.
  • Keep the appliance out of reach of children.
  • Do not immerse the appliance in water or any other liquid.
  • Do not operate the appliance if it has been damaged in any way.

Parts and Accessories

Your Breville InFizz Aqua Sparkling Water Maker includes the following components:

  • Breville InFizz Aqua Sparkling Water Maker unit
  • 1L / 34oz Carbonating Bottle with stainless steel cap and base
  • Cleaning Brush

Compatible Accessories (Sold Separately):

  • Standard screw-type 60L CO2 canisters (CO2 canister not included with purchase)
  • Additional 1L / 34oz Breville Carbonating Bottles
Two Breville carbonating bottles of different sizes

Image: Two Breville carbonating bottles, one 1L and one smaller, both with stainless steel bases and caps. These are available separately for storing more sparkling water.

Setup Instructions

1. Unpacking

Carefully remove all packaging materials from the appliance. Ensure all parts listed in the "Parts and Accessories" section are present. Dispose of packaging responsibly.

2. Installing the CO2 Canister

  1. Place the InFizz Aqua on a flat, stable surface.
  2. Remove the back cover of the appliance by gently pulling it away from the main unit.
  3. Unscrew the protective cap from the CO2 canister (not included).
  4. Carefully screw the CO2 canister into the designated compartment until it is firmly secured. Do not overtighten.
  5. Replace the back cover, ensuring it clicks into place.

3. Preparing the Carbonating Bottle

Before first use, wash the carbonating bottle with warm water and a mild detergent. Rinse thoroughly. Fill the bottle with cold tap water up to the fill line.

Operating Instructions

1. Attaching the Carbonating Bottle

  1. Ensure the carbonating bottle is filled with cold water up to the fill line.
  2. Tilt the carbonating bottle slightly and insert it into the carbonation head.
  3. Twist the bottle clockwise until it locks securely into place. The unique twist and lock system ensures a tight seal.
Hand twisting a Breville carbonating bottle into the sparkling water maker

Image: A hand demonstrates the unique twist and lock system, securing the carbonating bottle into the Breville InFizz Aqua for carbonation.

2. Carbonating the Water

  1. Once the bottle is securely attached, firmly press down the die-cast lever located at the top of the appliance.
  2. Hold the lever down for 1-2 seconds, then release. You will hear a hissing sound as CO2 is infused into the water.
  3. Repeat this process 2-3 times for light carbonation, or 4-5 times for stronger carbonation. Adjust based on your preference.
  4. A distinct buzzing sound indicates that the maximum carbonation level has been reached and excess pressure is being released.
Close-up of the Breville InFizz Aqua's brushed stainless steel lever

Image: A close-up view of the Breville InFizz Aqua's brushed stainless steel body and die-cast lever, highlighting the premium materials and operational component.

3. Removing the Carbonating Bottle

  1. After carbonation, wait a few seconds for any residual pressure to release.
  2. Gently twist the carbonating bottle counter-clockwise to unlock it from the carbonation head.
  3. Remove the bottle and enjoy your sparkling water.
  4. For best results, store carbonated water in the refrigerator.

Maintenance and Cleaning

1. Cleaning the Appliance

  • Wipe the exterior of the InFizz Aqua with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Do not immerse the appliance in water.

2. Cleaning the Carbonating Bottle

  • Wash the carbonating bottle with warm water and a mild dish soap using the provided cleaning brush.
  • Rinse thoroughly.
  • Note: The carbonating bottle is not dishwasher safe. Hand wash only.

3. Cleaning the Magnetic Drip Tray

The magnetic drip tray is removable for easy cleaning.

  1. Gently lift the magnetic drip tray from the base of the appliance.
  2. Wash with warm, soapy water and rinse thoroughly.
  3. Dry completely before reattaching to the base.
Close-up of the Breville InFizz Aqua's magnetic drip tray

Image: A close-up view of the Breville InFizz Aqua's magnetic, stainless steel drip tray, designed to catch spills and easily removable for cleaning.

Troubleshooting

ProblemPossible CauseSolution
No fizz or weak carbonationCO2 canister is empty or not properly installed. Bottle not securely attached. Water not cold enough.Replace CO2 canister. Ensure canister is screwed in tightly. Twist bottle firmly until locked. Use cold water for best carbonation. Press lever more times for stronger fizz.
Water sprays out during carbonationBottle overfilled. Bottle not securely attached.Ensure water is filled only to the fill line. Twist bottle firmly until locked.
Difficulty attaching/detaching bottleBottle not aligned correctly.Ensure the bottle is tilted slightly and aligned with the carbonation head before twisting. Do not force.

Specifications

  • Model Name: InFizz Aqua
  • Model Number: BCA600BSS
  • Brand: Breville
  • Material: Stainless Steel
  • Color: Brushed Stainless Steel
  • Capacity: 1 Liter (Carbonating Bottle)
  • Power Source: Manual (No electricity or batteries required)
  • Product Dimensions: 10.31"D x 6.02"W x 16.93"H
  • Item Weight: 7.68 pounds (3.49 Kilograms)
  • Compatible CO2 Canisters: Standard screw-type 60L CO2 canisters
Diagram showing the dimensions of the Breville InFizz Aqua Sparkling Water Maker

Image: A diagram illustrating the product dimensions of the Breville InFizz Aqua: 16.9 inches high, 6 inches wide, and 10.3 inches deep.

Warranty and Support

Your Breville InFizz Aqua Sparkling Water Maker comes with a 2-Year Product Warranty.

For warranty claims, technical support, or further assistance, please contact Breville Customer Service. Refer to the official Breville website or your purchase documentation for current contact information.

Online Resources: For additional tips, recipes, and product information, visit the official Breville website: www.breville.com

© 2025 Breville. All rights reserved.