Ant Esports Pepper 5F Mid-Tower Computer Case User Manual
Model: Pepper 5F
1. Introduction
The Ant Esports Pepper 5F is a mid-tower computer case designed to accommodate a variety of PC builds, including gaming systems. It supports ATX, Micro-ATX, and Mini-ITX motherboards and features a modern design with tempered glass panels. This manual provides essential information for setting up, operating, and maintaining your computer case.
Key features include:
- Mid-Tower design with dimensions of 390 x 200 x 450 mm.
- Stylish front and side tempered glass panels.
- Pre-installed 5 ARGB fans for enhanced cooling and aesthetics.
- Support for ATX, Micro-ATX, and Mini-ITX motherboards.
- Ample storage options with 2 HDD + 2 SSD or 4 SSD drive bays.
- Front I/O panel with 1 x USB 3.0, 2 x USB 2.0, and 1 x Audio + Mic TRRS Port.
- 7 expansion slots for various add-on cards.
Image 1.1: Ant Esports Pepper 5F Mid-Tower Computer Case (Black/White variant shown).
2. Setup Instructions
Follow these steps to assemble your computer components within the Ant Esports Pepper 5F case.
2.1 Motherboard Installation
The case supports ATX, Micro-ATX, and Mini-ITX motherboards. Install your motherboard onto the pre-installed standoffs. Ensure all mounting screws are securely fastened.
Image 2.1: Diagram illustrating motherboard size compatibility (Mini-ITX, Micro-ATX, ATX).
2.2 Drive Installation
The case provides bays for 2 x 3.5" Hard Disk Drives (HDDs) and 2 x 2.5" Solid State Drives (SSDs). Secure your drives in the designated mounting locations using the provided screws.
Image 2.2: Internal view showing dedicated bays for HDDs and SSDs, and PSU mounting area.
2.3 Power Supply Unit (PSU) Installation
Install your Power Supply Unit (PSU) into the dedicated shroud area at the bottom rear of the case. The case supports PSUs up to 200mm in length. Ensure all power cables are routed efficiently for optimal cable management.
Image 2.3: View of the full mesh PSU shroud, designed for improved airflow and aesthetics.
2.4 Fan Configuration and Airflow
The Ant Esports Pepper 5F comes with 5 pre-installed ARGB fans: 2 x 120mm in the front, 2 x 120mm on top, and 1 x 120mm in the rear. The case supports additional fan configurations for optimal air circulation:
- Front: 3 x 120mm or 2 x 140mm
- Top: 2 x 120mm or 1 x 140mm
- Bottom: 2 x 120mm
- Rear: 1 x 120mm
For liquid cooling, the case supports up to a 280mm radiator at the top and a 120mm radiator at the rear. Cold air intake is primarily through the bottom mesh, with hot air exhausting through the top and back.
Image 2.4: Diagram showing multiple fan mounting positions for optimal airflow.
Image 2.5: Illustration of cold air intake from the bottom and hot air exhaust from top and rear.
2.5 I/O Panel Connections
Connect the front I/O panel cables (USB 3.0, USB 2.0, Audio/Mic, Power, Reset) to the corresponding headers on your motherboard. Refer to your motherboard manual for specific header locations.
Image 2.6: Diagram showing the top I/O ports: USB 3.0, USB 2.0, Audio/Mic, Reset Button, and Power Button.
2.6 Expansion Card Installation
The case provides 7 expansion slots for installing graphics cards and other PCI-E devices. The maximum supported VGA card length is 320mm. Remove the necessary slot covers before installing your cards.
Image 2.7: Rear view highlighting the 7 expansion slots.
2.7 CPU Cooler Installation
Ensure that your CPU cooler height does not exceed 155mm to fit comfortably within the case.
Image 2.8: Diagram showing maximum CPU cooler height (155mm) and VGA card length (320mm).
3. Operating Instructions
Once all components are installed and connected, you can begin operating your system.
3.1 Power On/Off
Press the Power Button on the top I/O panel to turn your computer on or off.
3.2 Using I/O Ports
The front I/O panel provides convenient access to:
- USB 3.0 Port: For high-speed data transfer with compatible devices.
- USB 2.0 Ports (x2): For connecting standard USB peripherals.
- Audio + Mic TRRS Port: For connecting headsets with a combined audio/microphone jack.
3.3 ARGB Fan Control
The pre-installed ARGB fans can be controlled in two ways:
- Motherboard ARGB Header: If your motherboard has a 3-pin 5V ARGB header, connect the fan's ARGB cable to it. You can then control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync).
- Case Reset Button: If your motherboard does not have an ARGB header, the case's reset button can be connected to the fan's RGB controller. Pressing the reset button will cycle through various pre-set ARGB lighting modes. Note that this method typically offers limited control over individual colors or advanced effects.
4. Maintenance
Regular maintenance helps ensure optimal performance and longevity of your computer case.
4.1 Dust Filter Cleaning
The Ant Esports Pepper 5F features a magnetic dust filter on the top panel. Regularly remove and clean this filter to prevent dust buildup inside the case, which can impede airflow and component cooling. Simply lift the magnetic filter, clean it with water or a soft brush, and reattach it.
Image 4.1: Magnetic air filter located on the top panel for easy removal and cleaning.
4.2 General Cleaning
Use a soft, dry, anti-static cloth to clean the exterior surfaces of the case, including the tempered glass panels. Avoid using abrasive cleaners or solvents, as these can damage the finish or glass.
5. Troubleshooting
If you encounter issues with your Ant Esports Pepper 5F case, refer to the following common troubleshooting steps:
5.1 Fans Not Spinning or ARGB Not Lighting Up
- Power Connection: Ensure all fan power cables are securely connected to your power supply unit (PSU) or motherboard fan headers. Some fans may use Molex connectors directly from the PSU.
- ARGB Connection: Verify that the ARGB cables are correctly connected. If using a motherboard ARGB header, ensure it's a 3-pin 5V header and not a 4-pin 12V RGB header, as incorrect connection can damage the LEDs. If using the case's reset button for ARGB control, confirm it is properly connected to the fan's RGB controller.
- Software Control: If connected to a motherboard ARGB header, check your motherboard's RGB control software for fan lighting settings.
5.2 No Power to System
- PSU Connection: Ensure the PSU is properly installed, switched on, and all power cables are securely connected to the motherboard and components.
- Front Panel Cables: Double-check that the Power Button cable from the front I/O panel is correctly connected to the corresponding pins on your motherboard.
5.3 Front I/O Ports Not Functioning
- Cable Connection: Verify that the USB and audio cables from the front I/O panel are securely connected to the correct headers on your motherboard. Refer to your motherboard manual for header locations.
6. Specifications
Detailed specifications for the Ant Esports Pepper 5F Mid-Tower Computer Case:
| Feature | Specification |
|---|---|
| Model Name | Pepper 5F |
| Case Type | Mid Tower |
| Dimensions (D x W x H) | 390 x 200 x 450 mm |
| Motherboard Compatibility | ATX, Micro ATX, Mini ITX |
| Enclosure Material | Tempered Glass, ABS, SPCC |
| Drive Bays | 2 x 3.5 Inches (HDD), 2 x 2.5 Inches (SSD) or 4 x 2.5 Inches (SSD) |
| Pre-Installed Fans | 5 ARGB Fans (2x Front 120mm, 2x Top 120mm, 1x Rear 120mm) |
| Fan Support (Max) | Front: 3x120mm / 2x140mm, Top: 2x120mm / 1x140mm, Bottom: 2x120mm, Rear: 1x120mm |
| Liquid Cooling Support (Max) | Front: Up to 360mm, Top: Up to 280mm, Rear: 120mm |
| I/O Panel | 1 x USB 3.0, 2 x USB 2.0, 1 x Audio + Mic TRRS Port, Power Button, Reset Button |
| Expansion Slots | 7 |
| Max VGA Card Length | 320 mm |
| Max CPU Cooler Height | 155 mm |
| Cooling Method | Air |
| Special Features | Dust Filter (Magnetic Top Filter) |
| Item Weight | 4.8 Kilograms |
Image 6.1: Front and side view with key dimensions (450mm H x 200mm W x 390mm D).
7. Warranty and Support
This product is covered by a manufacturer's warranty and support services.
- Warranty Period: 1 Year
- Manufacturer: Ant Esports
- Importer: Acro Engineering Company
- For technical support, warranty claims, or further assistance, please contact Ant Esports directly through their official website or customer service channels.