Introduction
Thank you for choosing the Bazargame Bottom Loading Water Cooler Dispenser. This manual provides essential information for the proper installation, operation, maintenance, and troubleshooting of your new appliance. Please read this manual thoroughly before use and retain it for future reference.
Figure 1: Front view of the Bazargame Bottom Loading Water Cooler Dispenser, showing the concealed 5-gallon water bottle compartment.
1. Setup Instructions
- Unpacking: Carefully remove the dispenser from its packaging. Inspect for any damage during transit.
- Placement: Place the dispenser on a flat, stable surface. Ensure there is adequate ventilation around the unit, at least 10 cm (4 inches) from walls or other objects. Avoid direct sunlight or heat sources.
- Initial Cleaning: Before first use, clean the water reservoir and spouts. Refer to the "Maintenance" section for detailed cleaning instructions.
- Water Bottle Installation:
- Open the lower door of the dispenser.
- Remove the cap from a standard 5-gallon water bottle.
- Insert the water probe (tube) into the bottle opening. Ensure a secure fit.
- Slide the bottle into the compartment and close the door.
Figure 2: Detail of the water probe being inserted into a 5-gallon water bottle.
- Power Connection: Plug the power cord into a grounded electrical outlet.
- Filling the Reservoir: Allow several minutes for the internal reservoirs to fill with water from the bottle. Dispense a small amount of water from each spout (hot, cold, room temperature) to ensure air is purged and water flows freely.
2. Operating Instructions
2.1 Temperature Settings
This dispenser offers three temperature options:
- Hot Water: Dispenses water heated to 85-95°C (185-203°F). Ideal for tea, coffee, or instant meals.
- Cold Water: Dispenses chilled water at 5-10°C (41-50°F). Perfect for refreshing drinks.
- Room Temperature Water: Dispenses water at ambient temperature.
Figure 3: Overview of the three temperature settings and their typical ranges.
2.2 Dispensing Water
- Place a cup or container under the desired spout.
- Press the corresponding lever for hot (red), room temperature (white), or cold (blue) water. For hot water, a safety lock may need to be disengaged first (if applicable to your model).
- Release the lever to stop the water flow.
2.3 Indicator Lights
The dispenser features an indicator panel to show its operational status:
- POWER: Indicates the unit is powered on.
- HOT: Illuminates when the hot water heating element is active.
- COLD: Illuminates when the cold water cooling element is active.
- NO WATER: Flashes or illuminates when the 5-gallon bottle is empty and needs replacement.
Figure 4: Close-up of the LED indicator panel displaying operational status.
2.4 Heating and Cooling Switches
Separate ON/OFF switches for heating and cooling functions are located at the back of the unit. You can turn off either function if not needed to conserve energy.
Figure 5: Green (cooling) and red (heating) ON/OFF switches located on the back panel.
3. Maintenance
Regular maintenance ensures optimal performance and hygiene of your water dispenser.
3.1 Cleaning the Exterior
- Unplug the dispenser before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth. Do not use abrasive cleaners or solvents.
3.2 Cleaning the Removable Drip Tray
The drip tray collects spilled water and should be cleaned regularly.
- Remove the drip tray from its position below the spouts.
- Empty any collected water and wash the tray with mild soap and warm water.
- Rinse thoroughly and dry before reinserting.
Figure 6: The removable water tray, designed for easy cleaning of spills.
3.3 Internal Cleaning (Descaling)
It is recommended to clean and descale the internal water tanks every 3-6 months, or more frequently in areas with hard water.
- Unplug the dispenser and remove the water bottle.
- Drain all water from the hot and cold tanks using the drain plugs located at the back of the unit (if available).
- Prepare a cleaning solution: Mix 1 gallon of water with 2 tablespoons of white vinegar or a food-grade descaling agent.
- Pour the cleaning solution into the water reservoir (where the bottle normally connects).
- Allow the solution to sit for 15-30 minutes.
- Drain the cleaning solution completely from all spouts and drain plugs.
- Rinse the tanks thoroughly by filling with clean water and draining several times until no vinegar smell remains.
- Reinstall the water bottle and plug in the dispenser.
4. Troubleshooting
Before contacting customer support, please refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No water dispensing | Water bottle empty or not properly installed. Air lock in the system. | Replace the water bottle. Ensure the water probe is fully inserted. Dispense water from all spouts to release air. |
| Water not hot/cold enough | Heating/cooling switch is off. Unit recently plugged in. Ambient temperature too high/low. | Ensure the respective ON/OFF switch at the back is on. Allow 15-30 minutes for water to reach desired temperature. Ensure proper ventilation. |
| Water leakage | Water bottle cracked or seal broken. Drip tray overflowing. Loose connections. | Check water bottle for damage. Empty and clean drip tray. Inspect water lines for loose connections (contact support if unsure). |
| Unusual noise | Compressor cycling (normal). Unit not level. | Some noise during heating/cooling cycles is normal. Ensure the unit is on a level surface. |
| "NO WATER" indicator on, but bottle is full | Water probe not fully submerged or blocked. Sensor malfunction. | Re-seat the water probe. Ensure it reaches the bottom of the bottle. If issue persists, contact support. |
5. Specifications
| Feature | Detail |
|---|---|
| Brand | Bazargame |
| Model Number | Bottom Loading Water Cooler Dispenser (B0D73GH4TK) |
| Color | White |
| Material | Polypropylene (PP) |
| Capacity | Designed for 5 Gallon Bottles |
| Product Dimensions (D x W x H) | 36.41" x 12.2" x 11.61" |
| Style | Bottom Load |
| Wattage (Heating) | 500 watts |
| Wattage (Cooling) | 90 watts |
| Installation Type | Freestanding |
| Number of Temperature Settings | 3 (Hot, Cold, Room Temperature) |
| Hot Water Temperature Range | 85-95°C (185-203°F) |
| Cold Water Temperature Range | 5-10°C (41-50°F) |
| Hot Water Capacity | 5L/1.32Gal/H |
| Cold Water Capacity | 2L/0.53Gal/H |
| Power Source | Corded Electric |
Figure 7: Visual representation of the dispenser's dimensions and key electrical specifications.
6. Warranty Information
Specific warranty details are typically provided with your purchase documentation. Please refer to the warranty card or contact the retailer for information regarding the warranty period and coverage for your Bazargame Water Cooler Dispenser. Keep your proof of purchase for warranty claims.
7. Customer Support
If you encounter any issues not covered in the troubleshooting section or require further assistance, please contact Bazargame customer support through your retailer or the official Bazargame website. When contacting support, please have your model number (B0D73GH4TK) and purchase date available.
For more information, you may visit the Bazargame Store on Amazon.