Paslode Cordless Finish Nailer Bonus Kit

Introduction

The Paslode Cordless Finish Nailer Bonus Kit is designed for precision and efficiency in various trim applications. This kit provides the freedom of cordless operation, allowing for maneuverability in tight spaces and challenging work environments. The system, including the nailer, nails, and fuel cell, is engineered to work together for consistent and accurate results.

Image: The complete Paslode Cordless Finish Nailer Bonus Kit, showcasing the nailer, fuel cells, lithium-ion battery, charger, and a box of 2.5-inch finishing nails.

Key features include:

• Precise Nail Placement: The angled magazine allows access to tight spots, enabling accurate nail placement for crown molding or baseboard in corners.
• Durability: The included 2.5-inch finishing nails are galvanized to resist corrosion when used in trimming woods.
• Extended Run Time: The nailer can drive up to 12,000 nails per charge with Paslode Finish Nailing Systems.
• Fast Charging: The Li-ion battery charges in approximately 1.5 hours, with a 2-minute quick charge providing up to 200 additional shots.
• Quick and Easy Fuel Loading: Fuel cells provide non-stop nailing for up to 1,000 nails per cell, designed for simple load-and-go operation.

General Safety Guidelines

Always follow these safety precautions to prevent injury and ensure safe operation of the nailer.

• Read the Manual: Before operating the tool, read and understand all instructions and safety warnings in this manual.
• Wear Eye Protection: Always wear ANSI Z87.1 approved safety glasses with side shields.
• Wear Hearing Protection: Prolonged exposure to noise from power tools can cause hearing damage.
• Wear Head Protection: A hard hat is recommended in environments where falling objects are a risk.
• Keep Work Area Clear: Ensure your work area is well-lit and free of clutter.
• Stay Alert: Do not operate the tool when tired or under the influence of drugs, alcohol, or medication.
• Secure Workpiece: Always secure the material you are working on to prevent movement.
• Disconnect Power: Always disconnect the battery and remove the fuel cell before performing maintenance, clearing jams, or when the tool is not in use.
• Use Correct Fasteners: Only use fasteners specified for this tool.
• Avoid Accidental Firing: Keep fingers away from the trigger when not actively driving fasteners.
• Proper Ventilation: Use in a well-ventilated area, especially when using fuel cells, to avoid inhaling fumes.

Kit Components

Your Paslode Cordless Finish Nailer Bonus Kit includes the following items:

• Paslode 16 Gauge Angled Cordless Li-ion Finish Nailer: The primary tool for driving finishing nails.
• Universal Short Yellow Trim Fuel (2-pack): Provides the necessary combustion to drive nails.
• 2,000 2.5 inch 20 Degree Angled Galvanized 16 Gauge Finishing Nails: Fasteners designed for trim applications.
• Lithium Ion Battery: Powers the electronic components of the nailer.
• Battery Charger: For recharging the lithium-ion battery.

Image: The Paslode 16 Gauge Angled Cordless Finish Nailer, highlighting its ergonomic design and angled magazine.

Image: A 2-pack of Paslode Universal Short Yellow Trim Fuel cells, essential for the nailer's operation.

Image: The Paslode Lithium Ion Battery, featuring its compact design and power switch.

Image: The Paslode Lithium Ion Battery Charger, with indicator lights for charging status.

Image: A box of Paslode 2.5-inch 16 Gauge Angled Finish Nails, showing the galvanized finish and angled collation.

Setup

1. Charging the Battery

1. Connect the battery charger to a standard electrical outlet.
2. Insert the Paslode Lithium Ion Battery into the charger. The indicator light on the charger will show the charging status.
3. A full charge typically takes about 1.5 hours. A 2-minute quick charge can provide enough power for approximately 200 shots.
4. Once fully charged, remove the battery from the charger.

2. Installing the Fuel Cell

1. Ensure the battery is inserted into the nailer.
2. Open the fuel cell compartment on the nailer.
3. Insert a Universal Short Yellow Trim Fuel cell into the compartment, ensuring it is seated correctly. The fuel cell is designed for easy, non-stop nailing.
4. Close the fuel cell compartment securely.

3. Loading Nails

1. Pull back the nail pusher until it locks into place.
2. Insert a strip of 2.5-inch 16 Gauge Angled Finishing Nails into the magazine. Ensure the nails are oriented correctly with the points facing forward.
3. Release the nail pusher, allowing it to push the nails forward into the firing position.

Image: The Paslode nailer demonstrating the 'Convenient Load & Go' feature, showing how the fuel cell and nails are inserted into the tool.

Operating the Nailer

1. Powering On

Ensure the battery is fully charged and inserted, and a fuel cell is installed. The nailer is ready for use once these components are in place.

2. Adjusting Depth of Drive

The depth of nail drive can be adjusted to suit different materials and desired finishes. Locate the depth adjustment mechanism, typically a dial or lever near the nose of the tool. Turn or slide it to increase or decrease the nail's penetration depth. Test on a scrap piece of material before final application.

3. Firing the Nailer

1. Place the nose of the nailer firmly against the workpiece at the desired nailing location.
2. Squeeze the trigger to fire a nail. The nailer is designed for precise nail placement, even in tight corners.
3. Allow the tool to reset between shots for optimal performance.

4. Best Practices

• Always hold the tool firmly with both hands if possible.
• Maintain a stable stance.
• Avoid firing into knots or extremely hard materials that could cause nail deflection or tool damage.
• Regularly check the nail and fuel levels to avoid interruptions.

Maintenance

Proper maintenance ensures the longevity and reliable performance of your Paslode nailer.

1. Cleaning

• Daily: Wipe down the exterior of the tool with a clean, dry cloth to remove dust and debris.
• Regularly: Periodically clean the nosepiece and magazine area to prevent buildup of wood dust or nail residue that could cause jams. Use compressed air if available.

2. Lubrication

Refer to the specific lubrication instructions provided with your nailer. Paslode tools often require specific types of oil for internal components. Do not over-lubricate.

3. Storage

• Always remove the battery and fuel cell before storing the tool.
• Store the nailer in a clean, dry place, away from extreme temperatures and direct sunlight.
• Keep the tool out of reach of children.

Troubleshooting

This section addresses common issues you might encounter with your Paslode Cordless Finish Nailer.

If problems persist after attempting these solutions, please contact Paslode customer support.

Specifications

Warranty and Support

For detailed warranty information and customer support, please refer to the warranty card included with your product or visit the official Paslode website. Keep your proof of purchase for any warranty claims.

Online Resources: Visit the Paslode Store on Amazon