Bandai Hobby HG 1/144 Gundam EX (RFV) Model Kit Instruction Manual

Introduction

This instruction manual provides essential information for the assembly, operation, and maintenance of your Bandai Hobby HG 1/144 Gundam EX (RFV) model kit. Please read through these instructions carefully before beginning assembly to ensure a successful and enjoyable building experience. This model kit allows for the recreation of intricate details and dynamic action poses of the Gundam EX from the series Gundam: Requiem for Vengeance.

Figure 1: Fully assembled Gundam EX (RFV) model kit.

Safety Information

WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years.

This product contains small components that may pose a choking hazard. Adult supervision is recommended during assembly, especially for younger builders. Keep all parts and packaging materials away from small children.

What's in the Box

The Bandai Hobby HG 1/144 Gundam EX (RFV) model kit includes the following components:

• Gundam: Requiem for Vengeance - #255 Gundam EX (RFV) HG 1/144 model kit parts (on runners)
• Beam Rifles x1
• Beam Sabers (Grips) x3
• Shield x1
• Hand parts x1 set
• Instruction Manual (this document)
• Marking stickers

Figure 2: Included accessories and weapon parts.

Assembly (Setup)

Assembly of this model kit requires careful attention to detail. Refer to the included printed instruction manual for step-by-step diagrams and part identification. Basic tools such as plastic nippers are recommended for cleanly removing parts from the runners. A panel lining marker can be used to enhance the visual detail of the model.

General Assembly Steps:

1. Carefully cut each part from its runner using plastic nippers. Avoid pulling or twisting parts to prevent damage.
2. Smooth any remaining nubs on the parts using a hobby knife or sandpaper if desired.
3. Follow the numerical and pictorial instructions in the printed manual to connect parts.
4. Apply marking stickers as indicated in the manual to replicate the Mobile Suit's appearance.
5. Assemble the main body, limbs, head, and accessories according to the diagrams.

Figure 3: Front view of the assembled model.

Figure 4: Rear view of the assembled model, highlighting weapon storage.

Features (Operating)

The Gundam EX (RFV) model kit is designed with several articulated features for dynamic posing and display:

• Movable Beam Saber Rack: The Beam Saber Rack on the back is movable, allowing for the recreation of unsheathing poses.


Figure 5: Movable Beam Saber Rack.

• Flexible Ammunition Belt: The ammunition belt for the gatling gun is crafted from soft materials, enabling it to bend along with the barrel’s movements, enhancing realism.


Figure 6: Flexible ammunition belt detail.

• Detailed Shield and Weapon Attachment: The back of the shield features intricate detailing. The main weapon (rifle) can be attached to the back of the waist for storage or dynamic posing.


Figure 7: Shield with intricate back detailing.



Figure 8: Rifle attached to the back of the waist.

• Dynamic Posing: The model's articulation allows for a wide range of poses, including combat stances with beam sabers and rifles, as well as kneeling positions. An action base (sold separately) can be used for more dynamic aerial or action displays.


Figure 9: Gundam EX in a beam saber pose.



Figure 10: Dynamic display using an action base.

Maintenance

To ensure the longevity and appearance of your Gundam EX model kit, follow these maintenance guidelines:

• Cleaning: Dust the model regularly with a soft brush or compressed air. Avoid using harsh chemicals or abrasive materials, which can damage the plastic or paint.
• Handling: Handle the model by its main body whenever possible. Avoid excessive force on joints or thin parts to prevent breakage.
• Storage: Store the model away from direct sunlight, extreme temperatures, and high humidity to prevent discoloration or warping of plastic parts.
• Joint Tightening: If joints become loose over time, a thin layer of clear topcoat or clear nail polish can be applied to the joint pegs to increase friction. Allow to dry completely before reassembling.

Troubleshooting

Here are solutions to common issues encountered during or after assembly:

• Parts Not Fitting: Ensure parts are correctly oriented and that no excess plastic (nubs) remains from the runners. Do not force parts together; gently trim or sand if necessary.
• Loose Joints: Refer to the "Joint Tightening" tip in the Maintenance section.
• Sticker Application Issues: Use tweezers for precise placement of stickers. If a sticker does not adhere well, ensure the surface is clean and dry.
• Missing or Damaged Parts: If you encounter missing or damaged parts, please contact the retailer or Bandai Spirits customer support with your product information and proof of purchase.

Specifications

Warranty and Support

This product is an officially licensed Bandai Spirits product. For product support assistance within the United States, purchasers are entitled to support when purchasing from authorized U.S. Retailers. The product box will feature a Bandai Namco warning label as proof of official licensing. Please retain your proof of purchase for any support inquiries.