Ecoflow Control Module VCS-ECOMOD User Manual

1. Product Overview

The VCS-ECOMOD is a replacement Ecoflow RF Control Module designed for use with various fireplace systems, including Superior, Astria, Lennox, and IHP models. This module is a critical component for managing the electronic functions of your fireplace, ensuring reliable and safe operation of the ignition and control systems.

It is manufactured by Vavle Control Systems and is intended as a direct replacement part to restore or maintain the functionality of compatible fireplace units.

Figure 1: Top view of the VCS-ECOMOD control module. The label clearly displays "VALVE CONTROL SYSTEMS VCS", "MODEL VCS-ECOMOD", "DATE CODE 2244", and detailed "CONTROL WIRING" instructions (LEARN - BLACK, IGN/CONT PILOT - YELLOW, GND - BLUE, ON/OFF - BROWN). Electrical ratings are also visible: "CONTROL VOLTAGE INPUT: 6VDC, 0.8AMPS", "GAS VALVE OUTPUT: 6VDC, 0.8AMPS". The module is marked for "FOR INDOOR OR OUTDOOR USE" and includes ANSI Z21.20 and FCC certifications.

2. Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

• Always disconnect power to the fireplace unit before attempting any installation, maintenance, or service.
• Installation and service must be performed by a qualified installer, service agency, or gas supplier.
• Ensure all wiring connections comply with local codes and ordinances.
• Do not operate the fireplace if any part is submerged in water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been submerged in water.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.

3. Specifications

4. Installation and Setup

This control module is a replacement part and should be installed by a qualified professional. Incorrect installation can lead to system malfunction, property damage, or personal injury. Refer to your fireplace unit's specific installation manual for detailed instructions on replacing control modules.

General Installation Steps:

1. Power Disconnection: Ensure the main power supply to the fireplace unit is completely disconnected at the circuit breaker or fuse box. Verify with a voltage tester.
2. Access Module: Locate the existing control module within your fireplace system. This may require removing access panels or grates.
3. Disconnect Old Module: Carefully disconnect all wiring harnesses and connections from the old module. Note the position and color of each wire if not clearly labeled. The VCS-ECOMOD label provides specific wiring for LEARN (BLACK), IGN/CONT PILOT (YELLOW), GND (BLUE), and ON/OFF (BROWN).
4. Install New Module: Secure the new VCS-ECOMOD module in the same location as the old one.
5. Connect Wiring: Reconnect all wiring harnesses and individual wires to the new module, ensuring they match the original configuration and the labels on the module.
6. Secure Connections: Double-check all connections for tightness and proper seating.
7. Restore Power: Once the module is securely installed and all connections are verified, restore power to the fireplace unit.
8. Test Operation: Follow your fireplace unit's instructions to test the functionality of the new control module, including ignition, flame control, and remote operation (if applicable).

Figure 2: Side view of the VCS-ECOMOD module. This angle highlights the various connection ports and the battery compartment, which may be used for backup power or specific functions depending on the fireplace system.

Figure 3: Close-up of the power and switch terminals on the VCS-ECOMOD. These terminals are crucial for connecting the module to the fireplace's power supply and control switches, enabling the system to receive commands and operate correctly.

5. Operation

The VCS-ECOMOD control module functions as the central electronic brain for your fireplace's ignition and control system. Its operation is typically integrated with your fireplace's existing controls, such as wall switches, remote controls, or thermostat connections.

Once properly installed and powered, the module will respond to signals from these controls to initiate ignition sequences, manage flame height (if applicable), and ensure safe shutdown. Refer to your specific fireplace model's user manual for detailed instructions on how to operate your fireplace with the new control module.

Figure 4: An alternative view of the VCS-ECOMOD module, highlighting the battery compartment (labeled "BATT") and other connection points. This perspective provides a comprehensive look at the module's various interfaces for integration into a fireplace system.

6. Maintenance

The VCS-ECOMOD control module is designed for long-term reliability and typically requires minimal maintenance. However, periodic checks can help ensure its continued performance:

• Visual Inspection: Annually, or during routine fireplace maintenance, visually inspect the module and its connections for any signs of wear, corrosion, or damage. Ensure all wires are securely connected.
• Cleanliness: Keep the area around the module free from dust, debris, and moisture. Use a soft, dry cloth to gently wipe the exterior of the module if necessary. Do not use liquid cleaners.
• Battery Check (if applicable): If your fireplace system or the module itself utilizes backup batteries, check and replace them as recommended by your fireplace manufacturer to ensure continuous operation during power outages.

Always disconnect power before performing any maintenance.

7. Troubleshooting

If your fireplace system is not operating correctly after installing the VCS-ECOMOD module, consider the following basic troubleshooting steps. For complex issues, always consult a qualified service technician.

• No Power/No Response:
  • Verify that the main power supply to the fireplace is on.
  • Check all wiring connections to the module for tightness and correct placement.
  • Ensure any batteries (if used in the system or module) are fresh and correctly installed.
• Intermittent Operation:
  • Inspect for loose connections or damaged wiring.
  • Ensure the module is securely mounted and not subject to excessive vibration.
• FCC Interference:
  • If experiencing interference, try reorienting or relocating the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

If problems persist, contact a certified fireplace technician or the manufacturer for assistance.

8. Warranty and Support

For specific warranty information regarding your VCS-ECOMOD control module, please refer to the documentation provided with your purchase or contact All Pro Fireplace directly. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.

For technical support, installation guidance, or to inquire about replacement parts, please contact:

All Pro Fireplace
(Contact information not provided in product data, please refer to your purchase receipt or the seller's website for current contact details.)

When contacting support, please have your product model number (VCS-ECOMOD) and purchase details readily available.