Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your RMSPO Dado Throat Plate, model 089240028701. This accessory is designed to enhance the functionality of compatible Ridgid table saws by allowing the safe and efficient use of dado blade sets. Please read this manual thoroughly before use to ensure proper installation and safe operation.
Important Safety Information
Always prioritize safety when working with power tools. Failure to follow these safety guidelines may result in serious injury or damage to equipment.
- Read Your Table Saw Manual: Always refer to your Ridgid table saw's original instruction manual for specific safety warnings and operating procedures.
- Eye Protection: Always wear appropriate eye protection (safety glasses or goggles) when operating a table saw.
- Unplug Before Installation: Ensure the table saw is unplugged from the power source before installing or removing the dado throat plate.
- Secure Fit: Verify that the dado throat plate is securely seated and level with the table saw surface before operation.
- Proper Blade Selection: Use only dado blade sets that are compatible with your table saw and the 1-inch slot width of this throat plate.
- Keep Hands Clear: Never place hands near the saw blade during operation. Use push sticks or push blocks as necessary.
Package Contents
Your package should contain the following item:
- 1 x RMSPO Dado Throat Plate (Model 089240028701)
Image: Top-down view of the RMSPO Dado Throat Plate, model 089240028701.
Compatibility
This RMSPO Dado Throat Plate (089240028701) is specifically designed for compatibility with the following Ridgid table saw models:
- Ridgid R4514
- Ridgid R4514T
- Ridgid R4518
- Ridgid R4518T
- Ridgid R4518NS
Image: The dado throat plate correctly fitted into a compatible Ridgid table saw.
Setup and Installation
Follow these steps to properly install the dado throat plate:
- Ensure Safety: Unplug your Ridgid table saw from the power outlet before beginning installation.
- Remove Existing Plate: Locate the existing throat plate on your table saw. Typically, there is a latch or lever to release it. Carefully remove the standard throat plate.
- Insert Dado Throat Plate: Position the RMSPO Dado Throat Plate into the opening on the table saw. Ensure it aligns correctly with the mounting points.
- Secure the Plate: Press down firmly to seat the plate. The plate features a knob with a small notch designed to catch under the table surface, securing it in place.
- Leveling: Use the integrated leveling screws (typically adjusted with a 2mm Allen wrench) to ensure the dado throat plate is perfectly flush with the surface of your table saw. Adjust each screw until there is no lip or gap between the plate and the table.
- Final Check: Once installed, gently push on the plate to confirm it is stable and does not rock or shift.
Image: A close-up view demonstrating the ease of installation and removal of the dado throat plate.
Operating Instructions
This dado throat plate is designed for use with dado blade sets to create grooves, rabbets, and other wide cuts.
- Install Dado Blades: With the table saw unplugged, install your dado blade set according to your table saw's manufacturer instructions. Ensure the dado blade width does not exceed the 1-inch slot width of the throat plate.
- Adjust Blade Height: Carefully raise the dado blade set through the slot of the dado throat plate to the desired cutting height.
- Perform Test Cuts: Always perform test cuts on scrap material to verify the depth and width of your dado cut before working on your final workpiece.
- Maintain Control: Use appropriate push sticks and featherboards to maintain control of your workpiece and keep hands away from the blade.
Image: A dado blade set in operation, demonstrating precise and efficient cutting with the dado throat plate.
Maintenance
Regular maintenance ensures the longevity and performance of your dado throat plate.
- Cleaning: After each use, remove the throat plate and clean any sawdust or debris from its surfaces and the table saw's throat plate recess. A brush or compressed air can be used.
- Inspection: Periodically inspect the throat plate for signs of wear, cracks, or damage. Ensure the leveling screws are intact and functional.
- Storage: Store the dado throat plate in a clean, dry place when not in use to prevent damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Throat plate does not fit or is loose. | Incorrect model compatibility; improper seating. | Verify your table saw model against the compatibility list. Ensure the plate is fully seated and the locking mechanism is engaged. |
| Throat plate is not flush with the table surface. | Leveling screws require adjustment. | Adjust the leveling screws using a 2mm Allen wrench until the plate is perfectly flush. |
| Dado blade does not fully extend. | Blade height limit reached; incorrect blade size. | Ensure your dado blade set is compatible with your table saw's maximum blade height. The throat plate has a 1-inch slot width. |
If you encounter issues not listed here or require further assistance, please contact RMSPO customer service.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 089240028701 |
| Brand | RMSPO |
| Material | Durable material (plastic with reinforcing ribs) |
| Item Weight | 5.6 ounces |
| Package Dimensions | 14.8 x 5.35 x 1.1 inches |
| Slot Width | 1 inch (for dado blades) |
| Compatibility | Ridgid R4514, R4514T, R4518, R4518T, R4518NS Table Saws |
Image: Diagram showing the dimensions of the dado throat plate: approximately 14 inches long and 3.23 inches wide.
Warranty and Customer Support
For information regarding warranty coverage, please refer to the product packaging or contact RMSPO directly. If you have any questions about this dado throat plate or require assistance, you can contact RMSPO customer service via email. We aim to reply within 24 hours.
Contact: Please refer to your purchase documentation or the RMSPO brand store for current contact information.