Teglu FHC-2000A Paraffin Wax Warmer Instruction Manual

Introduction

Thank you for choosing the Teglu FHC-2000A Paraffin Wax Warmer. This device is designed to provide a soothing and moisturizing paraffin wax treatment for your hands and feet. Please read this manual thoroughly before initial use to ensure safe operation and optimal performance. Keep this manual for future reference.

Important Safety Information

WARNING: Failure to follow these safety instructions may result in electric shock, fire, or serious injury.

• Always unplug the device from the power outlet immediately after use and before cleaning.
• Do not use this appliance near water, such as in a bathtub, shower, or sink.
• Never reach for an appliance that has fallen into water. Unplug it immediately.
• Do not operate the device if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged.
• Keep the cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
• The wax can reach high temperatures. Always test the wax temperature on a small area of your skin (e.g., wrist) before immersing hands or feet to prevent burns. The recommended comfortable temperature for skin contact is around 50-55°C (122-131°F).
• Do not use on irritated, sunburned, broken, or sensitive skin. Consult a physician if you have any skin conditions or circulatory problems.
• Keep out of reach of children. This appliance is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
• Use only paraffin wax specifically designed for paraffin baths. Do not use other types of wax or substances.
• Ensure the device is placed on a stable, heat-resistant surface during operation.
• Do not cover the device while it is operating.

Package Contents

Please check the package contents upon opening to ensure all items are present:

• 1x Teglu FHC-2000A Paraffin Wax Warmer (2L capacity)
• 3x 200g Paraffin Wax Packs
• 100x Plastic Hand Gloves
• 100x Plastic Foot Gloves
• 2x Thermal Gloves (for hands)
• 1x Silicone Brush (for cleaning)

Product Overview

The Teglu FHC-2000A features a compact design with intuitive controls for temperature and timer settings.

Setup Instructions

1. Unpack: Carefully remove the paraffin wax warmer and all accessories from the packaging.
2. Placement: Place the warmer on a flat, stable, and heat-resistant surface. Ensure there is adequate ventilation around the device.
3. Insert Wax: Open the lid and place the paraffin wax packs directly into the inner pot of the warmer. The 2L capacity can accommodate approximately 2-3 packs of 200g wax.
4. Connect Power: Plug the power cord into a standard electrical outlet.

Operating Instructions

1. Melting the Paraffin Wax

1. Power On: Press the "ON" button to turn on the device.
2. Set Temperature: Use the "+" or "-" buttons to set the desired melting temperature. For rapid melting, set the temperature to a higher value, up to 80°C. The 150W heating element can melt 2 packs of wax in approximately 30 minutes.
3. Monitor Melting: Allow the wax to melt completely. The device will maintain the set temperature.
4. Adjust for Use: Once the wax is fully melted, lower the temperature setting to a comfortable and safe range for skin application, typically between 50°C and 55°C. Wait approximately 10 minutes for the wax to cool to this temperature.
5. Test Temperature: Before immersing your hand or foot, carefully dip a finger into the wax to test the temperature. It should feel warm and comfortable, not hot.

2. Applying the Paraffin Wax Treatment

1. Prepare Skin: Ensure your hands or feet are clean and dry.
2. Dip: Slowly dip your hand or foot into the melted paraffin wax, ensuring full coverage. Immediately withdraw.
3. Repeat: Wait a few seconds for the wax to solidify slightly, then repeat the dipping process 3-5 times to build up a thick layer of wax.
4. Cover: Immediately after the final dip, place a plastic glove (provided) over the waxed hand or foot. For enhanced heat retention, then place a thermal glove (provided for hands) or a towel over the plastic glove.
5. Relax: Allow the wax to remain on your skin for 10-15 minutes. This allows the heat to penetrate and moisturize the skin.
6. Remove Wax: After 10-15 minutes, remove the thermal glove and plastic glove. The wax should peel off easily with the plastic glove. Discard the used wax. Do not reuse wax that has been in contact with skin.
7. Moisturize: Gently massage any remaining oils into your skin. Your skin should feel soft and moisturized.

3. Timer Reservation Mode

The device features a timer function to pre-set the heating time.

• Press the "ON" button.
• Press the timer button (often indicated by a clock icon or separate mode button) to enter reservation mode.
• Use the "+" or "-" buttons to set the desired delay time from 2 to 99 hours. The device will begin heating after the set time has elapsed.
• Caution: Due to the long duration options, ensure the device is placed safely and away from flammable materials if using the timer function for extended periods.

Maintenance

Cleaning the Wax Warmer

1. Unplug: Always unplug the device and allow it to cool completely before cleaning.
2. Remove Excess Wax: If there is unmelted wax remaining, reheat the machine briefly to soften the wax. Once slightly melted, turn off and unplug the device. Carefully remove any large pieces of wax.
3. Wipe Clean: Use the provided silicone brush or a soft, damp cloth to wipe the interior of the pot. Do not use abrasive cleaners or harsh chemicals.
4. Dry: Ensure the pot is completely dry before storing or next use.
5. Exterior: Wipe the exterior of the device with a soft, damp cloth.

Note: No special cleaning liquid is required. Do not immerse the device in water.

Troubleshooting

Specifications

Warranty and Support

This Teglu FHC-2000A Paraffin Wax Warmer comes with a standard manufacturer's warranty. Please refer to the warranty card included in your package for specific terms and conditions, including the warranty period and coverage details.

For technical support, troubleshooting assistance, or warranty claims, please contact Teglu customer service through the retailer where you purchased the product or visit the official Teglu website for contact information.

Please have your model number (FHC-2000A) and purchase date ready when contacting support.