PioneerWorks 44" Gas Fire Pit Table Instruction Manual

1. Important Safety Information

Please read and understand all safety warnings and instructions before assembling, operating, or servicing this fire pit table. Failure to follow these instructions may result in property damage, personal injury, or death.

• For outdoor use only. Do not use this appliance indoors.
• Keep away from combustible materials. Maintain a minimum clearance of 36 inches (91 cm) from the top and sides to any combustible surfaces.
• Ensure proper ventilation when in use. Do not obstruct the airflow around the fire pit.
• Do not move the fire pit while in operation or when hot. Allow the unit to cool completely before moving.
• Follow all local codes and regulations for propane tank storage and handling.
• Keep children and pets away from the fire pit when in use and while cooling down.
• Always use the provided glass fire stones. Do not use other materials in the burner pan.
• Never leave the fire pit unattended when lit.
• Do not store a spare propane cylinder under or near this appliance.
• Inspect the hose before each use. If there is evidence of excessive abrasion or wear, or if the hose is cut, it must be replaced prior to putting the appliance into operation.

2. Package Contents

Verify that all components are present and undamaged before assembly. If any parts are missing or damaged, do not attempt to assemble or operate the fire pit. Contact customer support for assistance.

• Fire Pit Table Base (with integrated burner and control panel)
• Slate Table Top
• Double-sided Lid (Metal/Slate)
• Blue Glass Fire Stones
• Propane Tank Holder Ring
• Waterproof Rain Cover
• Assembly Hardware (bolts, washers, nuts, wrench)

3. Assembly Instructions

Assembly typically requires two people. Ensure you have adequate space and all tools provided or required.

1. Unpack Components: Carefully remove all parts from the packaging. Place them on a soft, clean surface to prevent scratches.
2. Assemble Base: Follow the diagrams in your specific assembly guide to connect the side panels and support frames of the fire pit table base. Secure all connections with the provided hardware.
3. Install Propane Tank Holder: Inside the cabinet, secure the propane tank holder ring to the base using the designated screws. This ring will stabilize the 20 lb propane tank.
4. Attach Table Top: Carefully place the slate table top onto the assembled base. Align the pre-drilled holes and secure the top using the provided bolts and washers.
5. Place Burner Pan: Ensure the stainless steel burner pan is correctly seated in the opening of the table top.
6. Add Glass Fire Stones: Distribute the crystal blue fire glass evenly over the burner pan. Do not cover the igniter or thermocouple.

4. Setup

Before operating, ensure the fire pit is properly set up in a safe location.

1. Position the Fire Pit: Place the fire pit table on a flat, stable, non-combustible surface outdoors. Ensure it is away from any overhead obstructions or combustible materials.
2. Install Propane Tank: Open the double doors of the fire pit table. Place a standard 20 lb propane tank (not included) into the tank holder ring.
3. Connect Gas Line: Connect the regulator hose from the fire pit to the propane tank valve. Hand-tighten the connection firmly. Do not use tools to tighten, as this may damage the connection.
4. Leak Test: Before first use and after any tank change, perform a leak test. Apply a soapy water solution to all gas connections. Open the propane tank valve slowly. If bubbles appear, there is a leak. Close the tank valve immediately and tighten connections. Repeat the test. If leaks persist, do not operate the fire pit and contact customer support.

5. Operating Instructions

This fire pit features an efficient electronic ignition system for easy startup.

1. Prepare for Ignition: Ensure the propane tank valve is fully open. Remove the double-sided lid from the burner area.
2. Ignite the Burner: Locate the hidden control knob on the side of the fire pit. Push the pulse switch (igniter button) and simultaneously turn the control knob counter-clockwise to the 'LOW' position. Hold the igniter button for a few seconds until the flame ignites.
3. Adjust Flame: Once ignited, release the igniter button. You can adjust the flame height by turning the control knob between 'LOW' and 'HIGH' settings.
4. Shut Down: To turn off the fire pit, turn the control knob clockwise to the 'OFF' position. Then, close the valve on the propane tank. Allow the unit to cool completely before covering or moving.

6. Maintenance

Regular maintenance ensures the longevity and safe operation of your fire pit table.

• Cleaning: After the unit has cooled, wipe down the slate top and steel base with a soft, damp cloth. For stubborn stains, use a mild soap solution. Avoid abrasive cleaners or harsh chemicals.
• Burner Maintenance: Periodically inspect the burner and gas orifices for blockages (e.g., spider webs, debris). Clean with a soft brush if necessary.
• Glass Fire Stones: The crystal blue fire stones can be rinsed with water and allowed to dry completely before being placed back in the burner pan.
• Storage: When not in use, especially during inclement weather or off-season, cover the fire pit with the provided waterproof rain cover. Store the propane tank in a well-ventilated area, away from direct sunlight and heat sources, and disconnected from the fire pit.

7. Troubleshooting

If you encounter issues, refer to the following common problems and solutions.

8. Specifications

9. Warranty and Support

PioneerWorks products are manufactured to high-quality standards. For specific warranty details, please refer to the warranty card included with your purchase or visit the official PioneerWorks website.

For technical assistance, missing parts, or any questions regarding your PioneerWorks 44" Gas Fire Pit Table, please contact our customer support team. You can find contact information on our official brand store: PioneerWorks Store.