1. Introduction
This document provides essential information for the ALLIANCE LAUNDRY SYSTEMS Washer, part number 39249. This component is a flat washer designed for specific applications within various laundry appliances. It serves to distribute the load of a threaded fastener, reduce vibration, and prevent loosening, or to provide spacing. This manual covers its intended use, installation considerations, maintenance, and specifications.
The washer is compatible with a range of laundry systems, including Speed Queen, IPSO, Cissell, Huebsch, Unimac, Econo-Wash, and Primus appliances.
2. Product Overview
Figure 1: Alliance Laundry Systems Washer, part number 39249. This image displays the Alliance Laundry Systems Washer, part number 39249. It is a flat, circular metal component with a central opening, designed for use in various laundry appliances.
The washer is a small, circular component made of durable material, featuring a central hole. Its precise dimensions (.280 inch inner diameter, .87 inch outer diameter, and .06 inch thickness) are critical for its function in specific applications within laundry equipment.
3. Setup and Installation
This washer is a replacement part. Installation typically involves replacing an existing worn or damaged washer within a laundry appliance. Always ensure the appliance is disconnected from power and water supplies before beginning any installation or repair work.
Safety Precautions:
- Disconnect the appliance from all power sources before installation.
- Turn off water supply valves if working on water-related components.
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- Refer to the specific service manual for your laundry appliance model for detailed disassembly and reassembly instructions.
Installation Steps (General):
- Identify the location of the washer to be replaced within the appliance.
- Carefully remove any fasteners or components obstructing access to the old washer.
- Remove the old washer, noting its orientation and position.
- Clean the area where the new washer will be installed, removing any debris or corrosion.
- Place the new ALLIANCE LAUNDRY SYSTEMS Washer 39249 in the correct position.
- Reassemble all components and fasteners, ensuring they are tightened to the manufacturer's specifications (refer to your appliance's service manual).
- Restore power and water supply, then test the appliance for proper function and absence of leaks.
4. Operating Principles
As a component part, the washer itself does not have operational controls. Its function is passive but critical to the integrity and performance of the larger laundry appliance. It ensures proper spacing, reduces friction, and helps maintain the tightness of bolted joints, preventing wear and potential leaks in areas where it is installed.
5. Maintenance
Regular inspection of the washer and surrounding components is recommended during routine appliance maintenance or when other parts are being serviced.
Inspection Points:
- Wear: Check for signs of thinning, deformation, or excessive wear.
- Corrosion: Inspect for rust or other forms of corrosion, especially in damp environments.
- Damage: Look for cracks, bends, or any physical damage that could compromise its function.
- Proper Seating: Ensure the washer is still seated correctly and not displaced.
If any of these conditions are observed, the washer should be replaced with a genuine ALLIANCE LAUNDRY SYSTEMS part 39249 to ensure continued optimal performance and safety of the appliance.
6. Troubleshooting
Issues directly attributable to a faulty washer are typically related to its failure to perform its intended function, leading to secondary problems within the appliance.
Potential Symptoms of a Faulty Washer:
- Leaks: If the washer is part of a water-tight seal or connection, a worn or damaged washer can lead to water leaks.
- Loose Connections: A deformed or missing washer can cause bolted joints to loosen over time, leading to rattling noises or instability of components.
- Increased Wear on Adjacent Parts: Without proper spacing or load distribution, other components may experience accelerated wear.
If these symptoms are observed and traced back to the washer, replacement is the recommended solution.
7. Specifications
| Specification | Detail |
|---|---|
| Part Number | 39249 |
| Inner Diameter (ID) | 0.280 inches |
| Outer Diameter (OD) | 0.87 inches |
| Thickness | 0.06 inches |
| Manufacturer | Alliance Laundry Systems |
| Item Weight | 0.16 ounces |
| Package Dimensions | 6 x 6 x 4 inches |
| Item Package Quantity | 1 |
| ASIN | B0CYDHK858 |
| Date First Available | March 12, 2024 |
8. Warranty and Support
As an OEM (Original Equipment Manufacturer) part, this washer is manufactured by Alliance Laundry Systems. For specific warranty information regarding this component, please refer to the warranty documentation provided with your original appliance or contact Alliance Laundry Systems directly. Support for installation or troubleshooting should first be sought from the service manual of the appliance in which this part is used. For further assistance, contact the seller or Alliance Laundry Systems customer service.
Manufacturer: Alliance Laundry Systems
Contact: Refer to your appliance's documentation or the Alliance Laundry Systems official website for customer support contact information.
