Bazargame Commercial Electric Hot Water Dispenser

1. Introduction

Thank you for choosing the Bazargame Commercial Electric Hot Water Dispenser. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your new appliance. Please read this manual thoroughly before use and retain it for future reference.

Important Safety Information

• Always keep the product and the water source clean and sanitary.
• If the machine emits a burning smell, immediately disconnect the power and water source.
• Ensure the water source is connected before switching on the power.
• Dry burning is strictly prohibited! Operating the unit without water can cause severe damage.
• Read all precautions in this instruction manual carefully before initial use.

2. Product Overview

The Bazargame Commercial Electric Hot Water Dispenser is designed for efficient hot water and steam dispensing in commercial settings. It features an intelligent LCD screen, precise temperature control, and a timing function.

Included Components

• 1x Water Boiler Unit
• 1x English Manual
• 1x Inlet Pipe
• 1x Drip Tray

Key Features

• Timing Function: Program operation for 1-12 hours.
• Accurate Temperature Control: Set specific temperatures for various beverages (e.g., 140℉ for milk foam, 185℉ for coffee, 212℉ for boiled water, 131℉ for milk tea, 176℉ for extracted tea).
• Intelligent LCD Screen: Displays real-time water temperature and cup temperature.
• Steam Pressure Gauge: Provides real-time pressure readings.
• Safety Pressure Release: Automatic steam nozzle pressure release when pressure is too high.
• Fast Heating: 3000W power for rapid heating.
• Large Capacity: 12L (3.2 gallons) capacity.
• 360° Rotating Valves: Water and steam valves offer flexible positioning.
• Durable Construction: 304 Stainless Steel inner liner with foam insulation for heat retention.

Figure 2.1: Front view of the hot water dispenser, showing the control panel, water spout, and steam wand.

3. Specifications

Figure 3.1: Product dimensions, showing height, width, and depth measurements.

4. Setup

4.1 Assembly

The unit requires minor assembly. Please refer to the included English Manual for detailed assembly instructions for the drip tray and inlet pipe connection.

4.2 Water Connection

1. Ensure the unit is placed on a stable, level surface.
2. Connect the inlet pipe to a clean, potable water source. Ensure all connections are secure to prevent leaks.
3. Verify that the water pressure is within the specified range of 0.1-0.4 MPA.

4.3 Power Connection

1. Plug the power cord into a standard 110V electrical outlet.
2. Ensure the power outlet is properly grounded and can support a 3000W appliance.

5. Operation

Once the unit is properly set up and connected to water and power, you can begin operation.

5.1 Initial Start-up

1. Turn on the main power switch. The LCD screen will illuminate.
2. The unit will begin to fill with water and heat to the default temperature.

5.2 Temperature Control

Use the control panel buttons and polygonal knobs to adjust the desired water temperature. The intelligent LCD screen displays the current water temperature in real-time.

• Recommended Temperatures:
  • Milk Foam: 140℉ (60℃)
  • Coffee: 185℉ (85℃)
  • Boiled Water: 212℉ (100℃)
  • Milk Tea: 131℉ (55℃)
  • Extracted Tea: 176℉ (80℃)

5.3 Timing Function

The timing function allows you to set the dispenser to operate for a specific duration (1-12 hours). Consult the detailed instructions in the included manual for programming the timer.

5.4 Dispensing Hot Water and Steam

Both the hot water valve and steam valve can rotate 360° for convenience.

• Hot Water: Position a cup or container under the hot water spout and open the valve to dispense.
• Steam: Use the steam wand for frothing milk or other applications. Monitor the steam pressure gauge during use.

Figure 5.1: Dispensing hot water into a glass.

Figure 5.2: Dispensing hot water for coffee preparation.

6. Maintenance

6.1 Cleaning Instructions

To ensure longevity and hygiene, regular cleaning is essential.

• Product Care: Hand wash only. Wipe clean with a damp cloth.
• Exterior: Wipe the exterior surfaces with a soft, damp cloth. Avoid abrasive cleaners or solvents.
• Drip Tray: Regularly empty and clean the drip tray to prevent overflow and bacterial growth.
• Interior: For internal cleaning and descaling, refer to the detailed instructions in the main manual.

6.2 General Care

• Always disconnect the power before cleaning or performing any maintenance.
• Ensure the unit is completely cool before handling internal components.

7. Troubleshooting

This section addresses common issues you might encounter with your hot water dispenser.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase documentation or contact the seller directly. Keep your purchase receipt as proof of purchase.