Toshilian Roller Shutter Timer (Model 240357) User Manual

1. Introduction

This manual provides detailed instructions for the installation, setup, and operation of the Toshilian Roller Shutter Timer, Model 240357. This device is designed to control one rotary motor for roller shutters, awnings, or blinds, featuring a 24-hour/7-day programmable timer function. You can easily set a weekly schedule or a schedule for a specific day. It has 6 easy-to-use buttons and a large monochrome screen. The integrated power supply operates with an input power of 230 Volts. The controller is suitable for all usual tubular motors with two control lines (up/down), terminal phase, and neutral wires. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety Information

Important Safety Instructions:

• Installation must be performed by a qualified electrician in accordance with local electrical codes and regulations.
• Disconnect power at the main circuit breaker before performing any wiring or maintenance.
• Do not expose the device to moisture or extreme temperatures.
• Ensure the device is securely mounted.
• This device is designed for indoor use only.
• The maximum load capacity is 400 Watts. Do not exceed this limit.

3. Package Contents

Verify that all components are present:

• Toshilian Roller Shutter Timer (Model 240357)
• User Manual (this document)
• Mounting screws (if included)

4. Product Overview

The Toshilian Roller Shutter Timer features a clear monochrome display and six intuitive buttons for easy programming and control.

Figure 1: Front View of the Roller Shutter Timer. This image shows the device's front panel, featuring a digital display that shows the time and day, along with six control buttons: an 'Up' arrow, a 'Stop' square, a 'Down' arrow, and three smaller buttons below the display for menu navigation and setting adjustments.

4.1. Controls and Display

• Display: Monochrome screen showing time, day, and programming status.
• Up Button (▲): Moves the shutter up or navigates menus.
• Stop Button (■): Stops the shutter movement or confirms selections.
• Down Button (▼): Moves the shutter down or navigates menus.
• Programming Buttons (- • -): Used for setting time, programs, and other functions. (Specific functions will be detailed in the Operating section).

4.2. Rear Connections

Figure 2: Rear View and Wiring Terminals. This image displays the back of the timer unit, highlighting the green terminal block for electrical connections. A white label is visible, indicating "Vida XL", "Itemnumber: 240357", "Rated load: ≤400W", and "Voltage: AC230V/50Hz", along with a CE mark and a crossed-out wheeled bin symbol.

The rear of the device contains the terminal block for electrical connections. It is designed for standard tubular motors with two control lines (up/down), a phase terminal, and neutral wires.

5. Setup and Installation

WARNING: Electrical installation should only be performed by a qualified professional. Ensure power is disconnected before proceeding.

5.1. Mounting

1. Choose a suitable indoor location for mounting, away from direct sunlight, moisture, and heat sources.
2. Ensure there is sufficient space for wiring and operation.
3. Mount the timer securely to a wall or standard flush-mounted box using appropriate screws.

5.2. Wiring Diagram

The controller is compatible with standard tubular motors that have separate control lines for 'Up' and 'Down' movements, along with phase and neutral connections.

Wiring Connections:

• L (Live/Phase): Connect to the main power supply phase (230V AC).
• N (Neutral): Connect to the main power supply neutral.
• UP (Motor Up): Connect to the motor's 'Up' control wire.
• DOWN (Motor Down): Connect to the motor's 'Down' control wire.
• Ground: Ensure the motor and any metal parts are properly grounded according to local regulations.

Refer to the motor's instruction manual for specific wiring requirements.

5.3. Initial Power-Up

1. After completing all wiring, restore power at the main circuit breaker.
2. The display should illuminate. If not, check wiring and power supply.
3. The device may require initial time and date setting.

6. Operating Instructions

6.1. Setting Current Time and Day

1. Press and hold the central programming button (•) for a few seconds until the time display starts flashing.
2. Use the Up (▲) and Down (▼) buttons to adjust the hour. Press the central programming button (•) to confirm and move to minutes.
3. Adjust minutes using Up (▲) and Down (▼) buttons, then confirm with (•).
4. Proceed to set the current day of the week (e.g., Mo, Tu, We, Th, Fr, Sa, Su) in the same manner.
5. Press the central programming button (•) again to exit the time/day setting mode.

6.2. Manual Control

• Press the Up (▲) button once to move the shutter upwards.
• Press the Down (▼) button once to move the shutter downwards.
• Press the Stop (■) button once to halt the shutter movement at any desired position.

6.3. Programming Timer Schedules (24h/7d)

The device allows for setting weekly or daily schedules for automatic shutter operation.

1. Press the left programming button (-) to enter program setting mode. The display will show "P1" (Program 1) or similar.
2. Use the Up (▲) and Down (▼) buttons to select the desired program slot (e.g., P1, P2, etc.).
3. Press the central programming button (•) to edit the selected program.
4. Set Day(s): Use Up (▲) and Down (▼) to select the day(s) for this program (e.g., individual days, weekdays, weekends, all days). Confirm with (•).
5. Set UP Time: Adjust the hour and minutes for the shutter to move UP using Up (▲) and Down (▼), confirming each with (•).
6. Set DOWN Time: Adjust the hour and minutes for the shutter to move DOWN using Up (▲) and Down (▼), confirming each with (•).
7. Repeat for additional programs as needed.
8. Press the right programming button (-) or wait for a few seconds to exit programming mode.

Note: The exact number of programmable events and specific button sequences may vary slightly. Refer to the on-screen prompts for guidance.

6.4. Activating/Deactivating Programs

Typically, programs are active once set. Some models may have a dedicated button or menu option to enable/disable all programmed schedules. Consult the display for an indicator (e.g., a clock icon) showing active timer mode.

7. Maintenance

• Cleaning: Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Inspection: Periodically check for any visible damage to the casing or wiring. If damage is found, disconnect power and contact a qualified technician.
• Battery (if applicable): Some timers may have a small backup battery to retain settings during power outages. If the time/settings are frequently lost, the battery may need replacement by a qualified technician.

8. Troubleshooting

9. Technical Specifications

10. Warranty and Support

For warranty information and technical support, please refer to the documentation provided at the point of purchase or contact your retailer. Keep your proof of purchase for warranty claims.

Manufacturer: Toshilian

ASIN: B0CWZ6YWGC