Introduction
Thank you for choosing the BN-LINK Countdown Timer Switch (Model CP-U211C). This device is designed to provide convenient, energy-saving control for your exhaust fans, bathroom fans, and various lighting types. By automating shut-off operations, it helps reduce energy consumption and improve convenience in your home or office.
Please read this manual thoroughly before installation and operation to ensure proper use and safety.
Important Safety Information
WARNING: RISK OF ELECTRIC SHOCK.
- Installation must be performed by a qualified electrician or a person with a thorough understanding of electrical wiring and systems.
- Always turn off power at the circuit breaker or fuse box before installing or servicing the switch.
- This device requires a neutral wire for operation. If your existing switch box does not have a neutral wire, consult a qualified electrician.
- For single-pole applications only. Do not use with 3-way or multi-way switches.
- Ensure all wire connections are secure and properly insulated.
- Do not exceed the maximum electrical ratings of the device.
- Operating Voltage: 125V, 60 Hz.
- Current Rating: 15A/1875W Resistive or General Purpose, 10A/1250W Ballast or Tungsten, ½ HP, TV-5.
Setup & Installation
This section provides instructions for installing your BN-LINK Countdown Timer Switch. Ensure power is OFF before proceeding.
Package Contents:
- BN-LINK Countdown Timer Switch
- Wall Plate
- Mounting Screws
- Wire Nuts
Tools Required (Not Included):
- Screwdriver (Phillips and Flathead)
- Wire Strippers
- Electrical Tape
- Voltage Tester
Installation Steps:
- Turn Off Power: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off using a voltage tester.
- Remove Old Switch: Carefully remove the existing wall plate and unscrew the old switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal.
- Identify Wires: Identify the following wires in your wall box:
- Hot Wire (Line): Typically black, brings power from the circuit breaker.
- Load Wire: Typically black, sends power to the light/fan.
- Neutral Wire: Typically white. A neutral wire is REQUIRED for this switch.
- Ground Wire: Typically green or bare copper.
- Wire the New Switch: Connect the wires from your wall box to the BN-LINK timer switch using the provided wire nuts. Refer to the wiring diagram below.
- Connect the Black Wire from the timer switch to the Hot Wire (Line) from the wall box.
- Connect the Red Wire from the timer switch to the Load Wire from the wall box.
- Connect the White Wire from the timer switch to the Neutral Wire from the wall box.
- Connect the Green Wire from the timer switch to the Ground Wire from the wall box.
- Secure the Switch: Carefully fold the wires and push the timer switch into the wall box. Secure it with the mounting screws.
- Install Wall Plate: Attach the provided wall plate over the switch.
- Restore Power: Turn the power back ON at the circuit breaker.
- Test Operation: Test the timer switch to ensure it functions correctly.
Image: Wiring diagram for the BN-LINK Countdown Timer Switch. This diagram illustrates the connection points for the ground wire (green), load wire (red), hot wire (black), and neutral wire (white) to the timer switch. A clear warning states "Neutral Wire Must Required."
Operating Instructions
The BN-LINK Countdown Timer Switch features intuitive touch controls for easy operation.
Image: Front view of the BN-LINK Countdown Timer Switch, highlighting the "Touch ON/OFF Button" at the top and the six "Touch to select time" buttons (1 Min, 5 Min, 10 Min, 20 Min, 30 Min, 1 Hour). LED indicators are also shown, indicating which countdown is active.
Button Functions:
- Power Button (Top): This is the main ON/OFF button.
- Press once to turn the connected device (light/fan) ON indefinitely.
- Press again to turn the connected device OFF.
- This button can also override any active countdown timer, turning the device OFF immediately.
- Countdown Timer Buttons (1 Min, 5 Min, 10 Min, 20 Min, 30 Min, 1 Hour): These buttons activate a preset countdown.
- Press any of these buttons to turn the connected device ON for the selected duration.
- The device will automatically turn OFF once the countdown expires.
- An LED indicator next to the selected time will illuminate to show the active countdown.
Example Usage:
To turn on your bathroom fan for 10 minutes, simply press the "10 Min" button. The fan will run for 10 minutes and then automatically shut off. If you need to turn it off sooner, press the top Power button.
Versatile Applications
The BN-LINK Countdown Timer Switch is suitable for a wide range of applications, enhancing convenience and energy efficiency in various areas of your home or business.
Image: A collage of four images demonstrating common applications for the timer switch: a bathroom, a closet, a laundry room, and a garage. This illustrates the versatility of the product in different environments.
- Bathrooms: Control exhaust fans to reduce humidity and prevent mold growth.
- Closets & Pantries: Automatically turn off lights after a set time, preventing wasted energy.
- Garages: Manage lighting or ventilation systems.
- Laundry Rooms: Control exhaust fans or lighting.
- Spas & Enclosed Patios: Conveniently manage lighting or small ventilation units.
This timer switch is compatible with incandescent, fluorescent, and LED lighting, as well as bathroom exhaust fans and heaters within its specified electrical ratings.
Maintenance
The BN-LINK Countdown Timer Switch requires minimal maintenance.
- Cleaning: To clean the surface of the switch, gently wipe with a soft, damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or internal components.
- Inspection: Periodically inspect the switch and wall plate for any signs of damage or loose connections. If any issues are found, turn off power at the circuit breaker and consult a qualified electrician.
- No User-Serviceable Parts: There are no user-serviceable parts inside the switch. Do not attempt to open or repair the unit yourself.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
Switch does not turn ON/OFF. |
|
|
Countdown timer does not activate or device stays ON indefinitely. |
|
|
LED indicators are not working. |
|
|
Switch does not fit into the wall box. |
|
|
If you encounter problems not listed here or if the suggested solutions do not resolve the issue, please contact BN-LINK Customer Support.
Specifications
| Model Number | CP-U211C |
| Operating Voltage | 125V, 60 Hz |
| Current Rating | 15A/1875W Resistive or General Purpose |
| Ballast/Tungsten Rating | 10A/1250W |
| Motor Rating | ½ HP |
| TV Rating | TV-5 |
| Switch Type | Push Button (Touch Control) |
| Circuit Type | Single-pole |
| Neutral Wire Required | Yes |
| Certifications | ETL Listed |
| Material | Plastic, Metal |
| Color | White |
| Product Dimensions (L x W x H) | 7.01 x 3.99 x 4.39 cm (2.76 x 1.57 x 1.73 inches) |
| Operating Temperature | 5°F to 122°F (-15°C to 50°C) |
| International Protection Rating | IP54 |
Image: Detailed dimensions of the BN-LINK Countdown Timer Switch and its accompanying wall plate. The image shows the height (5 inches for plate, 2.76 inches for switch body), width (3.3 inches for plate, 1.57 inches for switch body), and depth (1.73 inches for switch body).
Warranty & Support
BN-LINK products are designed to meet high-quality standards. For warranty information or technical support, please contact BN-LINK customer service.
Please have your model number (CP-U211C) and purchase date available when contacting support.
Contact Information:
- Refer to the BN-LINK official website or product packaging for the most current contact details.
- Online support may be available through the BN-LINK brand store on Amazon or their official website.
