Safety 1st Turn and Go 360 ST Car Seat Instruction Manual

1. Introduction

This instruction manual provides essential information for the proper installation, use, and maintenance of your Safety 1st Turn and Go 360 ST Car Seat. Please read this manual thoroughly before using the car seat to ensure the safety and comfort of your child. This car seat is designed to adapt to your child's growth, offering three modes of use: rear-facing, forward-facing, and belt-positioning booster.

Figure 1: Safety 1st Turn and Go 360 ST Car Seat in its primary configuration.

2. Important Safety Information

Always prioritize your child's safety. This car seat meets or exceeds all federal safety standards and is National Highway Traffic Safety Administration (NHTSA) compliant. Failure to follow these instructions can result in serious injury or death.

• Always secure your child in the car seat using the harness system appropriate for their size and the car seat mode.
• Ensure the car seat is correctly installed in your vehicle according to the instructions for your chosen installation method (vehicle belt or LATCH).
• Never leave your child unattended in the car seat.
• Do not use the car seat if it has been involved in a crash, even if there is no visible damage.
• Register your car seat with Safety 1st to receive important safety updates and recall information.

3. Product Overview and Components

The Safety 1st Turn and Go 360 ST Car Seat features a unique rotational base for ease of use. Key components include:

• Car Seat Shell: The main body of the car seat.
• Rotational Base: Allows 360-degree rotation for easy child loading and unloading.
• Harness System: 5-point harness for securing the child.
• Headrest and Harness Adjustment: Integrated system for adjusting height.
• Infant Head and Wedge Pillows: Removable inserts for smaller infants.
• SecureTech™ Indicators: Red-to-green indicators for proper belt tension.
• Vehicle Belt Lock-Off: Integrated mechanism for secure vehicle belt installation.
• LATCH Connectors: For LATCH system installation.
• Top Tether: For forward-facing installation.
• Cup Holders: Removable and dishwasher-safe.

Figure 2: Front view of the car seat, showing the harness and cup holders.

Figure 3: Side view of the car seat, highlighting its profile and rotational base.

4. Setup and Preparation

Before installing the car seat, ensure it is properly prepared for your child's size and the intended mode of use.

4.1. Infant Pillow Usage

• The head pillow should only be used in rear-facing mode to provide a better fit for infants.
• The wedge pillow must be used in rear-facing mode and forward-facing mode for children up to 30 lbs.

Figure 4: The infant head and wedge pillows provide a snug fit for smaller children.

4.2. Buckle Slot Adjustment

The buckle has three slots. Choose the slot closest to your child's body for a secure fit. Refer to your instruction manual for detailed steps on changing buckle positions.

4.3. Headrest and Harness Height Adjustment

To adjust the headrest and harness height, you may need to unfold the bottom of the headrest pad to extend it. Ensure the harness straps are at or below your child's shoulders for rear-facing, and at or above for forward-facing.

Figure 5: The 10-position headrest and harness adjust simultaneously for a proper fit.

5. Installation

The Safety 1st Turn and Go 360 ST Car Seat can be installed using your vehicle's seat belt or the LATCH system. The base installation remains the same for all three modes of use.

5.1. Installing Base with Vehicle Belt

1. Place the car seat in your vehicle. The taller side of the base should always be against the back of the vehicle's seat.
2. Loosely attach the top tether hook to the vehicle's tether anchor. Refer to your vehicle manual for locations.
3. Squeeze the "Squeeze to Rotate" handle located on the front of the car seat base and swivel the seat to face you (side view).
4. Squeeze the release handle located on the front of the car seat while lifting the car seat off the base and flipping it over to the opposite side. The car seat is intentionally attached to the base via a connection cord and should not be removed.
5. First, open the vehicle belt lock-off by squeezing the handle and pulling it forward.
6. Weave the vehicle seat belt in and out of the gray belt path and buckle the belt. Ensure the belt is flat and not twisted.
7. Place your hand in the base and firmly push down on the base. Pull the seat belt parallel with the belt path to tighten and remove slack. The SecureTech™ tension indicators will begin to turn green as the vehicle belt is tightened.
8. Close the vehicle belt lock-off. Both SecureTech™ indicators will turn completely green when the vehicle belt is properly installed.
9. Check to confirm that the base is tightly installed. With your non-dominant hand, firmly grab the car seat base right at the belt path and push and pull from side to side. If the base moves more than one inch, you can try reinstalling or changing to a different seating location.
10. Lastly, tighten the top tether strap until the tether door is flush with the base.

5.2. Installing Base with LATCH

1. Place the car seat in your vehicle. The taller side of the base should always be against the back of the vehicle's seat.
2. Loosely attach the top tether hook to the vehicle's tether anchor. Refer to your vehicle manual for locations.
3. Squeeze the "Squeeze to Rotate" handle located on the front of the car seat base and swivel the seat to face you (side view).
4. Squeeze the release handle located on the front of the car seat while lifting the car seat off the base and flipping it over to the opposite side. The car seat is intentionally attached to the base via a connection cord and should not be removed.
5. Remove the lower anchor belt from its storage pocket.
6. Weave the LATCH connector with the adjuster in and out of the gray belt path and attach to the vehicle's lower anchors. Ensure the belt is flat and not twisted.
7. Place your hand in the base and firmly push down on the base. Pull the LATCH belt parallel with the belt path to tighten and remove slack. The SecureTech™ tension indicators will begin to turn green as the LATCH belt is tightened.
8. Both SecureTech™ indicators will turn completely green when the LATCH is properly installed.
9. Check to confirm that the base is tightly installed. With your non-dominant hand, firmly grab the car seat base right at the belt path and push and pull from side to side. If the base moves more than one inch, you can try reinstalling or changing to a different seating location.
10. Lastly, tighten the top tether strap until the tether door is flush with the base.

6. Operating Modes

The Safety 1st Turn and Go 360 ST Car Seat offers three modes of use to accommodate your child's growth:

• Rear-Facing Infant Car Seat: For children weighing 5–40 lbs. and 19”–40” tall.
• Forward-Facing Car Seat: For children weighing 22–65 lbs. and 29”–49” tall.
• Belt-Positioning Booster Seat: For children weighing 40-100 lbs. and 43”-52” tall.

Figure 6: Visual representation of the three modes of use for the car seat.

6.1. Rotation Feature

The SafetySwivel™ 360° rotational technology allows you to turn the car seat towards you for easier buckling and transferring of your child. Once the base is securely installed, you can rotate the car seat forward or rear-facing as needed. The rotation lock indicator will show a locked symbol when the car seat is locked into place.

Figure 7: The SafetySwivel™ 360° rotating seat allows for easy in and out access.

Figure 8: The rotation lock indicator ensures the seat is securely positioned.

6.2. Recline Positions

In rear-facing mode, there are five recline positions. To adjust the recline, squeeze the recline handle and push the top of the car seat back until the desired position is achieved.

7. Maintenance

Proper maintenance ensures the longevity and hygiene of your car seat.

• Seat Pad: The seat pad is machine-washable and dryer-safe for easy clean-up. Refer to the care label on the seat pad for specific washing instructions.
• Cup Holders: The removable cup holders are dishwasher-safe.
• Harness and Buckle: Wipe clean with a damp cloth. Do not use harsh chemicals or abrasives.
• Plastic and Metal Parts: Wipe clean with mild soap and water.

Figure 9: The seat pad is designed for easy removal and cleaning.

Figure 10: The cupholders can be easily removed for cleaning in a dishwasher.

8. Troubleshooting

If you encounter issues with your car seat, refer to the following common solutions:

• Loose Installation: If the car seat base moves more than one inch from side to side or front to back at the belt path, it is not installed tightly enough. Re-read the installation instructions carefully, ensuring you are pulling the belt parallel to the belt path to remove slack and that the SecureTech™ indicators turn completely green. You may also try installing the car seat in a different seating location in your vehicle.
• Harness Adjustment Difficulty: Ensure the harness straps are not twisted. Lubricate the buckle with warm water if it becomes sticky.
• Rotation Difficulty: Ensure the car seat base is properly installed and the rotation lock indicator is showing the unlocked symbol before attempting to rotate.

9. Specifications

10. Warranty and Support

For warranty information, product registration, or customer support, please visit the official Safety 1st website or contact their customer service department. Keeping your proof of purchase is recommended for warranty claims.

Official Website: www.safety1st.com