1. Introduction
The Lunderg Toilet Safety Rails are designed to provide stable support for individuals requiring assistance when using the toilet. This product is intended for seniors, post-surgery patients, and those with mobility challenges, enhancing bathroom safety and independence. The design prioritizes stability and ease of cleaning by attaching directly to the toilet.
Figure 1.1: Lunderg Toilet Safety Rails installed, demonstrating stability.
Figure 1.2: Product designed for individuals with mobility impairments, focusing on safety and support.
2. Important Safety Information
- Ensure all components are securely fastened before each use.
- Do not exceed the maximum weight capacity of 300 pounds.
- Verify compatibility with your toilet type before installation to prevent instability.
- Regularly inspect the rails for any signs of wear or damage. Discontinue use if damage is observed.
3. Product Compatibility
The Lunderg Toilet Safety Rails are designed to fit most standard round and elongated toilets with fixed/bolted toilet seats and flat-back tanks. A minimum of 2 inches (50mm) clearance is required between the toilet seat bolts and the tank. The distance between the toilet seat bolts should be between 4.6 inches (116mm) and 8.5 inches (216mm).
Incompatible Toilet Types:
- Quick-Release toilet seats
- Smart toilets
- Bidet toilets
- Toilets with hidden bolts
- Toilets with enclosed bases (skirted toilets)
- Toilets with irregular shapes or curved tanks
Figure 3.1: Visual guide for toilet compatibility and incompatible features.
Figure 3.2: Required bolt spacing for proper installation.
4. Package Contents
Please ensure all the following components are present before beginning installation:
- Stabilizing Plate (1)
- Vertical Support Posts (2)
- Adjustable Handrails with Wood Finish (2)
- Screw-in Pins/Fasteners (for securing to toilet seat bolts)
- Assembly Tools (e.g., screwdriver, wrench if needed)
Figure 4.1: All components of the Lunderg Toilet Safety Rails.
5. Installation Instructions
No power tools are required for assembly. All necessary tools are included.
- Prepare the Toilet: Carefully remove your existing toilet seat by unscrewing the bolts at the back of the toilet bowl. Keep the original bolts and washers, as they may be reused.
- Position the Stabilizing Plate: Place the Lunderg stabilizing plate over the toilet bolt holes at the back of the toilet bowl. Ensure it sits flat and is properly aligned.
- Reattach Toilet Seat: Place your original toilet seat back onto the toilet, aligning its holes with the stabilizing plate and the toilet bowl holes.
- Secure with Pins: Insert the provided screw-in pins through the toilet seat, the stabilizing plate, and into the toilet bowl holes. Tighten them securely using the included tools until the entire assembly is firm and wobble-free.
- Attach Vertical Support Posts: Slide the vertical support posts onto the designated slots on the stabilizing plate.
- Attach Handrails: Insert the adjustable handrails into the top of the vertical support posts.
- Adjust Height: Adjust the height of the handrails to your preferred level (see Section 6).
- Final Check: Gently test the stability of the installed rails before full use. Ensure all connections are tight and the unit does not wobble.
Figure 5.1: Placing the stabilizing plate.
Figure 5.2: Reattaching the toilet seat.
Figure 5.3: Securing the assembly with screw-in pins.
6. Operation
Adjusting Handrail Height:
The handrails feature an adjustable height mechanism, ranging from 8.6 inches to 11.8 inches. To adjust, locate the adjustment knob on each vertical support post. Loosen the knob, slide the handrail to the desired height, and then securely tighten the knob to lock it in place. Ensure both handrails are adjusted to the same height for balanced support.
Figure 6.1: Adjustable handrails providing 20 inches of sitting space.
Figure 6.2: Adjusting the height of the handrail.
7. Care and Maintenance
The Lunderg Toilet Safety Rails are designed for easy cleaning due to their legless design, which prevents accumulation of dirt and debris on the floor.
- Clean the carbon steel frame and wood-finish handrails with a mild soap and water solution.
- Wipe dry with a soft cloth to prevent water spots and maintain the finish.
- Avoid using abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or material.
- Regularly check the tightness of all fasteners to ensure continued stability.
Figure 7.1: The legless design facilitates easier cleaning compared to floor-standing models.
8. Troubleshooting
Rails Feel Unstable:
- Ensure all screw-in pins securing the stabilizing plate and toilet seat are fully tightened.
- Verify that the vertical support posts and handrails are correctly seated and their adjustment knobs are tightened.
- Confirm that your toilet is compatible with the safety rails (refer to Section 3). Incompatibility can lead to instability.
Handrails Do Not Adjust Smoothly:
- Loosen the adjustment knob completely before attempting to slide the handrail.
- Check for any obstructions or debris within the adjustment mechanism.
9. Specifications
| Feature | Specification |
|---|---|
| Brand | Lunderg |
| Model Number | UPC-LUN-TOILETRAIL-NOLEGS |
| Material | Carbon Steel |
| Color | White |
| Finish Type | Wood Finish (Handrails) |
| Item Weight | 14.62 pounds (6.65 Kilograms) |
| Maximum Weight Capacity | 300 Pounds |
| Adjustable Handrail Height | 8.6 inches to 11.8 inches |
| Sitting Space Width | 20 inches |
| Package Dimensions | 25.5 x 10.6 x 7 inches |
10. Warranty and Customer Support
Lunderg offers a Lifetime Warranty for these Toilet Safety Rails, ensuring long-term reliability and customer satisfaction. For any inquiries, assistance, or warranty claims, please contact Lunderg customer service. Support is available 24/7.
Contact information can typically be found on the product packaging or the official Lunderg website.