1. Introduction
This manual provides essential information for the safe and effective use of your Jaspertronics Original VS16909 Lamp & Housing. This product is a high-quality replacement lamp module designed to restore optimal brightness and performance to compatible Viewsonic projectors. Please read these instructions carefully before installation and operation.
2. Safety Information
Observe the following safety precautions to prevent injury or damage to the product and your projector:
- Power Disconnection: Always disconnect the projector from the power outlet and allow it to cool down completely (at least 30 minutes) before attempting to replace the lamp.
- Hot Surface: Projector lamps operate at high temperatures. Do not touch the lamp immediately after use.
- Mercury Content: This lamp contains mercury. Handle with care and dispose of it according to local environmental regulations. Do not break the lamp.
- Eye Protection: Avoid looking directly into the lamp or projector lens when the lamp is operating, as intense light can cause eye damage.
- Proper Handling: Handle the lamp module by its housing. Avoid touching the glass bulb directly, as oils from your skin can reduce lamp life.
- Ventilation: Ensure the projector's ventilation openings are not blocked to prevent overheating.
3. Package Contents
Your package should contain the following item:
- One (1) Jaspertronics Original VS16909 Lamp & Housing
4. Compatible Projector Models
This lamp module is compatible with the following Viewsonic projector models:
- DX808ST, DX825ST
- MS550, MW550, MW605, MW605W, MW809ST, MW826ST, MW862ST
- MX550, MX604, MX604w, MX808PST, MX808ST, MX825ST
- PA500S, PA502SE, PA502XE, PA503S, PA503SP, PA503X, PA503XP, PA550X
- PG603X, PG703X, PG707X
- PS500X, PS501X, PS600X
- PX702HD, PX702HD-LAMP
- RLC-108, RLC-114, RLC-124
- VS16905, VS16909, 5JJGP05001
5. Specifications
| Feature | Specification |
|---|---|
| Brand | Jaspertronics |
| Model Name | VS16909-LAMP |
| Light Type | Metal Halide |
| Wattage | 200 Watts |
| Voltage | 120 Volts |
| Average Life | 5000 Hours |
| Bulb Shape Size | MR20 |
| Bulb Base | Prong |
| Material | Glass, Metal, Plastic |
| Dimensions | 6"W x 4"H |
| Item Weight | 0.99 Pounds (15.8 ounces) |
| Special Features | Easy Installation, Flicker-Free, Lightweight, Long Lasting |
6. Installation Instructions
Follow these steps to safely replace the lamp in your Viewsonic projector:
- Prepare the Projector: Ensure the projector is turned off and unplugged from the power source. Allow it to cool down for at least 30 minutes to prevent burns.
- Locate the Lamp Cover: Identify the lamp cover on your projector. This is typically secured by one or more screws.
- Remove the Lamp Cover: Unscrew the screw(s) on the lamp cover and carefully remove the cover. Keep the screws in a safe place.
- Loosen the Old Lamp: Locate the screws securing the old lamp module to the projector. Loosen these screws.
- Remove the Old Lamp: Gently pull the old lamp module straight out of the projector. Avoid forcing it.
- Insert the New Lamp: Carefully insert the new Jaspertronics VS16909 lamp module into the projector, ensuring it is seated correctly. Do not force it.
- Secure the New Lamp: Tighten the screws to secure the new lamp module in place.
- Replace the Lamp Cover: Place the lamp cover back onto the projector and secure it with the screw(s) removed earlier.
- Reset Lamp Timer: After installation, consult your projector's user manual to reset the lamp timer. This ensures accurate tracking of the new lamp's lifespan.
7. Operating Instructions
To maximize the lifespan and performance of your new lamp:
- Warm-up and Cool-down: Allow the projector to warm up for a few minutes after turning it on and cool down completely before unplugging or moving it. Avoid frequent on/off cycles.
- Environmental Conditions: Operate the projector in a clean, dust-free environment with adequate ventilation. Avoid extreme temperatures or humidity.
- Eco Mode: Utilize your projector's 'Eco Mode' or 'Low Power Mode' if available. This can extend lamp life by reducing brightness slightly.
8. Maintenance
Regular maintenance helps ensure optimal performance and longevity:
- Air Filter Cleaning: Periodically clean or replace the projector's air filter according to your projector's manual. A clogged filter can lead to overheating and reduced lamp life.
- Projector Cleaning: Keep the projector's exterior clean and free of dust. Use a soft, dry cloth. Do not use abrasive cleaners or solvents.
9. Troubleshooting
If you encounter issues after installing your new lamp, consider the following:
- No Light from Lamp:
- Ensure the lamp module is fully seated and secured.
- Verify the lamp cover is correctly installed and its screws are tightened. Many projectors have a safety switch that prevents operation if the cover is not secure.
- Check if the lamp timer was reset.
- Dim Image or Flickering:
- Confirm the projector is not in 'Eco Mode' if you desire maximum brightness.
- Check for any dust accumulation on the projector lens or inside the projector (refer to maintenance).
- Lamp Warning Indicator:
- If a lamp warning light persists after installation, ensure the lamp timer has been reset according to your projector's manual.
For further assistance, refer to your projector's original user manual or contact Jaspertronics customer support.
10. Warranty and Support
The Jaspertronics Original VS16909 Lamp & Housing comes with a 1-Year Warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical support, or any questions regarding your product, please contact Jaspertronics customer service through the retailer where the product was purchased or visit the official Jaspertronics website for contact information.