Enbrighten Z-Wave Plus Smart Light Switch User Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Enbrighten Z-Wave Plus In-Wall Smart Switch. This device is designed to enhance your home automation experience by providing wireless control of lighting and other devices when paired with a compatible Z-Wave hub.

The Enbrighten Z-Wave Plus Smart Switch features QuickFit and SimpleWire technologies for easier installation and improved compatibility with various home setups. It is compatible with popular Z-Wave certified hubs such as SmartThings, Ring Alarm, Wink, ADT Pulse, ADT Command, Trane, Vivint, Nexia, Honeywell, HomeSeer, and Harmony Home Hub Extender.

Safety Information

Before installation, read and understand all safety warnings and instructions. Improper installation or use can result in serious injury, death, or property damage.

• RISK OF ELECTRIC SHOCK: Electricity can cause personal injury and property damage if handled improperly. If you are unsure about any part of these instructions, please consult a qualified electrician.
• DISCONNECT POWER: Always turn OFF the power to the circuit at the service panel (circuit breaker) before beginning installation.
• USE INDOORS ONLY: This device is intended for indoor, in-wall installation only.
• NEUTRAL WIRE REQUIRED: A neutral wire is required for the proper operation of this switch. If your switch box does not have a neutral wire, consult a qualified electrician.
• COMPATIBILITY: Ensure the total wattage of the connected load does not exceed the switch's rating (15 Amps).

Features

• Voice Control Compatibility: Works with Alexa and Google Assistant (requires a Z-Wave certified hub).
• Versatile Applications: Control remotely via smartphone, voice commands, or manual ON/OFF. Supports custom scenes, scheduling, and alerts.
• Multi-Switch Setups: Integrates seamlessly into multi-switch setups with required add-on switches (models 12728 or 46200). Up to four add-on switches can be connected.
• Full-Home Coverage (Z-Wave Plus): Compatible with all previous Z-Wave generations. Extends Z-Wave signal range by up to 150ft, acting as a repeater.
• QuickFit Design: Easily fits in crowded switch boxes with 20% reduced housing and no break-off tabs.
• SimpleWire Technology: Faster installation with auto-detect line/load and dual, offset ground ports.
• LED Toggle Backlight: Features 4 selectable indicator light options.
• SmartStart: QR code and Device Specific Key allow easy, secure pairing.
• S2 Security: Industry-standard, 128-bit security provides safe installation.

Package Contents

• Enbrighten Z-Wave Plus Smart Switch (Model: 82686)
• Installation Screws
• Wire Nuts

Note: Wallplate not included. Add-on switches (models 12728 or 46200) sold separately for 3-way or 4-way installations.

Setup and Installation

Follow these steps carefully to install your Enbrighten Z-Wave Plus Smart Switch. If you are not comfortable with electrical wiring, please consult a qualified electrician.

1. Prepare for Installation

• Turn OFF power to the switch box at the circuit breaker or fuse box.
• Remove the existing wallplate and switch.
• Carefully label each wire connected to the old switch (Line/Hot, Load, Neutral, Ground, Traveler if applicable).
• Confirm the presence of a neutral wire (usually white) in the switch box. This switch requires a neutral wire.

2. Wiring the Smart Switch

The Enbrighten Smart Switch features SimpleWire technology for easier wiring. It has auto-detect line/load terminals.

Image Description: This diagram illustrates the QuickFit and SimpleWire features of the Enbrighten Smart Switch. The QuickFit section highlights the reduced housing and absence of break-off tabs for easier installation in crowded switch boxes. The SimpleWire section shows the wiring terminals: Ground (green), Load or Line (black), Traveler (optional for 3-way, red), and Neutral (white). It emphasizes faster installation with auto-detect line/load and dual, offset ground ports.

• Connect the bare copper or green wire from the wall box to the GROUND terminal on the switch.
• Connect the white wire from the wall box (NEUTRAL) to the NEUTRAL terminal on the switch.
• Connect the black wire from the wall box (LINE/HOT) to one of the LOAD/LINE terminals on the switch.
• Connect the black wire leading to the light fixture (LOAD) to the other LOAD/LINE terminal on the switch.
• For 3-Way or 4-Way Installations: If installing in a multi-switch setup, connect the traveler wire (usually red) from the wall box to the TRAVELER terminal on the smart switch. You will also need an Enbrighten add-on switch (models 12728 or 46200) for the other location(s). Refer to the add-on switch manual for its specific wiring.
• Ensure all wire connections are secure. The "poke-in" connections have screw tightening for added security.

3. Mounting and Finishing

• Carefully push the wired switch into the wall box.
• Secure the switch to the wall box using the provided screws.
• Attach the new wallplate (not included).
• Restore power to the circuit at the circuit breaker.

Image Description: This image provides detailed dimensions of the Enbrighten Smart Switch, including its height (4.13in/104.9mm), width (1.75in/44.5mm), and housing depth without yoke (1.13in/28.7mm). It also highlights key features such as the LED Toggle Backlight with 4 selectable indicator light options, the SmartStart QR code for easy pairing, and S2 Security for safe installation.

Image Description: This image illustrates two key functionalities of the Enbrighten Smart Switch. On the left, it shows the "3-Way Ready" feature, indicating the switch can control lights, fans, or appliances from up to five locations. On the right, it displays "Compatible Bulbs," showing that the switch works with dimmable, LED, CFL, incandescent, and halogen bulbs.

Operating Instructions

Manual Control

• Turn ON: Press the top of the toggle switch.
• Turn OFF: Press the bottom of the toggle switch.

The toggle switch is designed to return to the center position after activation.

Z-Wave Pairing (Inclusion)

To integrate your smart switch into your Z-Wave network, you must pair it with a compatible Z-Wave certified hub.

• Place your Z-Wave controller into inclusion (pairing) mode. Refer to your controller's manual for specific instructions.
• On the Enbrighten Smart Switch, press the top or bottom of the toggle switch once. The LED indicator will flash to confirm inclusion mode.
• The controller will confirm successful inclusion. The LED on the switch will stop flashing and remain solid or turn off, depending on its setting.
• If pairing is unsuccessful, repeat the steps or refer to the troubleshooting section.

Z-Wave Exclusion (Removal)

To remove the smart switch from your Z-Wave network:

• Place your Z-Wave controller into exclusion (removal) mode.
• On the Enbrighten Smart Switch, press the top or bottom of the toggle switch once. The LED indicator will flash to confirm exclusion mode.
• The controller will confirm successful exclusion.

Voice Control Integration

Once paired with a Z-Wave hub that supports Alexa or Google Assistant integration, you can control your switch using voice commands.

Image Description: This image depicts a family enjoying a movie night, with a voice bubble indicating a command: "Alexa, set theater lighting." Below the image, logos for "Works with Alexa" and "Works with Google Assistant" are displayed, emphasizing the product's compatibility with these voice control platforms. A note states that a compatible Z-Wave hub is required.

• Ensure your Z-Wave hub is linked to your Alexa or Google Assistant account.
• Discover new devices through your voice assistant app or by saying "Alexa, discover devices" or "Hey Google, sync my devices."
• Once discovered, you can use commands like:
  • "Alexa, turn on [Device Name]"
  • "Hey Google, turn off [Device Name]"
  • "Alexa, set [Device Name] to 50%" (Note: This switch is ON/OFF only, not a dimmer. Voice commands for dimming may not apply.)

Maintenance

• Clean the switch and wallplate with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Ensure the switch is not exposed to excessive moisture or extreme temperatures outside its operating range (32-104 degrees Fahrenheit).
• Regularly check for firmware updates for your Z-Wave hub, as these may improve compatibility and performance.

Troubleshooting

Specifications

Warranty and Support

This Enbrighten product is manufactured by Jasco Products Company, LLC. For warranty information or technical support, please refer to the contact information provided in your product packaging or visit the official Enbrighten website.

For additional support or to explore the full line of Enbrighten Z-Wave products, visit the Enbrighten Store on Amazon.