FIXIT PARTS W11729596 Ice Maker Kit Instruction Manual
For Whirlpool and Compatible Refrigerators
1. Product Overview
This manual provides instructions for the installation, operation, and maintenance of the FIXIT PARTS W11729596 Ice Maker Kit. This kit is designed to replace existing ice makers or add ice-making capability to compatible refrigerators.
1.1 What's in the Box
Ice maker assembly
Ice bucket
Jumper harness (includes 5, 8, and 4 PIN connectors)
Inlet valve
Fill tube
All mounting hardware (screws, brackets, etc.)
Image 1.1: All components included in the W11729596 Ice Maker Kit, featuring the ice maker assembly, ice bin, water inlet valve, fill tube, various connectors, and mounting hardware.
1.2 Compatible Brands and Models
The W11729596 Ice Maker Kit is compatible with various refrigerator brands, including:
Whirlpool
Kenmore
KitchenAid
Roper
Maytag
Estate
Inglis
Amana
Crosley
Magic Chef
This kit replaces part numbers W11510803, 2155468, 2155469, 2155469A, 2171811, 8560, ECKMF94, ECKMF95, IMKIT94, KIMS9, W10670871, W10715708, W11534202, and WPW10715708.
To ensure perfect fit and compatibility with your specific refrigerator model, it is recommended to verify the part number against your appliance's requirements or contact FIXIT PARTS customer support.
2. Safety Instructions
Always follow these safety precautions to prevent personal injury or property damage during installation and operation.
Disconnect Power: Always unplug the refrigerator from the electrical outlet before attempting any installation, maintenance, or repair.
Water Supply: Turn off the water supply to the refrigerator before disconnecting any water lines.
Wear Protective Gear: Use appropriate personal protective equipment, such as gloves and safety glasses, during installation.
Professional Assistance: If you are unsure about any step or encounter difficulties, consult a qualified appliance technician.
Proper Tools: Use only the correct tools for the job to avoid damaging components.
Inspect Components: Before installation, carefully inspect all parts for any signs of damage. Do not install damaged components.
3. Installation Guide
This section provides step-by-step instructions for installing the W11729596 Ice Maker Kit. Installation is designed to be straightforward, but careful attention to detail is required.
Ensure the refrigerator is unplugged and the water supply is turned off.
Clear the area around the refrigerator for easy access.
3.2 Step-by-Step Installation
Prepare the Refrigerator: If replacing an existing ice maker, carefully remove the old unit and any associated components. If installing in a refrigerator without a previous ice maker, locate the designated mounting area, typically in the freezer compartment.
Mount the Ice Maker Assembly: Secure the new ice maker assembly to the freezer wall using the provided mounting hardware. Ensure it is level and firmly attached.
Connect the Wiring Harness: Identify the correct wiring harness connector in your refrigerator. The kit includes 4-pin, 5-pin, and 8-pin connectors to ensure compatibility. Connect the appropriate jumper harness from the kit to the refrigerator's wiring and then to the ice maker assembly. Ensure connections are secure.
Image 3.1: The included jumper harness with 4-pin, 5-pin, and 8-pin connectors, designed for broad compatibility with various refrigerator models.
Install the Water Inlet Valve: Locate the water inlet connection point, typically at the back of the refrigerator. Mount the new water inlet valve using the provided hardware.
Connect Water Lines: Connect the refrigerator's main water supply line to the inlet side of the new valve. Then, connect the provided fill tube from the outlet side of the valve to the ice maker assembly. Ensure all connections are tight to prevent leaks.
Image 3.2: The ice bin, water inlet valve, and flexible fill tube, which directs water into the ice maker mold.
Position the Ice Bin: Place the ice bucket directly below the ice maker assembly, ensuring it is properly seated to catch ice as it is produced.
Final Checks: Double-check all electrical and water connections for security. Ensure no wires are pinched and no water lines are kinked.
Restore Power and Water: Turn on the water supply to the refrigerator. Plug the refrigerator back into the electrical outlet. Listen for any leaks and observe the ice maker's initial operation.
4. Operating Instructions
Once installed, the ice maker operates automatically. Allow several hours for the freezer compartment to reach the optimal temperature and for the first batch of ice to be produced.
Initial Ice Production: The first few batches of ice may be smaller or have an unusual taste. It is recommended to discard the first 2-3 batches of ice to flush the water lines and ensure optimal ice quality.
Ice Level Control: The ice maker typically has a shut-off arm or sensor that detects when the ice bin is full, automatically pausing ice production. When ice is removed, production will resume.
Temperature Settings: Ensure your freezer is set to the recommended temperature (typically 0°F / -18°C) for efficient ice production.
5. Care and Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your ice maker.
Cleaning the Ice Bin: Periodically remove and wash the ice bin with mild soap and warm water. Rinse thoroughly and dry completely before returning it to the freezer.
Checking Water Lines: Occasionally inspect the water lines for any kinks, leaks, or signs of wear.
Filter Replacement (if applicable): If your refrigerator has a water filter, ensure it is replaced according to the manufacturer's recommendations to maintain water quality and ice taste.
Seasonal Use: If you will be away for an extended period, it is advisable to turn off the ice maker and the water supply to the refrigerator.
6. Troubleshooting Guide
Refer to the table below for common issues and their potential solutions.
Problem
Possible Cause
Solution
No ice production
Refrigerator unplugged or power outage Water supply turned off or kinked line Freezer temperature too high Ice maker shut-off arm in 'off' position Faulty water inlet valve
Check power connection Ensure water supply is on and lines are clear Adjust freezer temperature to 0°F (-18°C) Lower the shut-off arm Inspect/replace water inlet valve
Small or hollow ice cubes
Low water pressure Partially clogged water filter Freezer temperature too high
Check household water pressure Replace water filter Adjust freezer temperature
Water leaks
Loose water line connections Cracked fill tube Faulty water inlet valve
Tighten all water line connections Inspect and replace fill tube if damaged Inspect/replace water inlet valve
Ice tastes bad or has odor
Old water filter Unclean ice bin Food odors in freezer
Replace water filter Clean ice bin thoroughly Store odorous foods in airtight containers
If troubleshooting steps do not resolve the issue, please contact FIXIT PARTS customer support for further assistance.
This FIXIT PARTS W11729596 Ice Maker Kit comes with a 1-year warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.
8.2 Customer Support
For any questions regarding product compatibility, installation assistance, troubleshooting, or warranty claims, please contact FIXIT PARTS customer support. Our team is available to provide expert guidance and support.
You can typically find contact information on the FIXIT PARTS official website or through your purchase platform.
