1. Introduction
This manual provides essential instructions for the safe and efficient use of your MineCtrl TiMOTION TP2 TP2P IP20 5 Pin AC/DC Switching Power Supply Transformer. This power supply is designed for use with various power recliners and lift chairs. Please read this manual thoroughly before installation and operation.
2. Safety Information
Please observe the following safety precautions to prevent injury or damage to the product:
- Electrical Shock Hazard: Do not open the power supply casing. Refer all servicing to qualified personnel.
- Dry Location Use Only: This device is intended for indoor use in dry locations only. Do not expose to water or excessive moisture.
- Proper Ventilation: Ensure adequate ventilation around the power supply to prevent overheating. Do not cover the unit.
- Correct Voltage: Only connect the power supply to an AC outlet providing 100-240V, 50/60Hz.
- Cable Integrity: Regularly inspect all cables for damage. Do not use if cables are frayed or damaged.
- Children and Pets: Keep the power supply and cables out of reach of children and pets.
3. Package Contents
Verify that all items are present in your package:
- 1 x MineCtrl TiMOTION TP2 Power Supply Unit
- 1 x AC Power Cord (for wall outlet connection)
- 1 x DC Output Cable with 5-Pin Female Plug
Image 3.1: Overview of the power supply unit, AC power cord, and DC output cable.
4. Setup Instructions
Follow these steps to correctly install your power supply:
- Connect the DC Output Cable: Locate the 5-pin female plug on the DC output cable. Connect this to the corresponding 5-pin male connector on your recliner or lift chair. Ensure a secure connection.
- Connect the AC Power Cord: Insert the 2-pin end of the AC power cord into the input port on the power supply unit.
- Plug into Wall Outlet: Plug the other end of the AC power cord into a standard electrical wall outlet (100-240V).
- Verify Power: A green LED indicator on the power supply unit should illuminate, indicating that the unit is receiving power and ready for operation.
Image 4.1: Detail of the 5-Pin female plug for connecting to the recliner.
Image 4.2: The AC power cord that connects to the power supply unit.
Video 4.1: Demonstration of connecting the power supply to a recliner and power outlet.
Video 4.2: Visual guide on connecting the AC power cord and DC output cable to the power supply and verifying the power indicator.
5. Operating Instructions
Once the power supply is correctly connected and the green LED is illuminated, your recliner is ready for use. Operate your recliner using its integrated controls as usual.
Video 5.1: Demonstration of a recliner operating with the power supply connected.
This power supply features a built-in battery backup function. To utilize this, install two 9V batteries (not included) into the designated compartment on the power supply unit. This allows for limited operation during power outages.
6. Maintenance
- Cleaning: Wipe the power supply unit with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
- Cable Inspection: Periodically check all cables for cuts, kinks, or signs of wear. Replace damaged cables immediately.
- Battery Replacement (for backup): If using the battery backup feature, replace the 9V batteries when their charge is depleted to ensure continued functionality during power interruptions.
7. Troubleshooting
If you encounter issues with your power supply, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Recliner does not operate. | No power to the unit; loose connections; faulty recliner motor/switch. | Check if the green LED on the power supply is lit. Ensure all cables are securely connected. Test the wall outlet with another device. If the issue persists, consult a qualified technician for recliner inspection. |
| Green LED is not lit. | Power cord not connected; wall outlet not active; power supply failure. | Ensure the AC power cord is fully inserted into both the power supply and the wall outlet. Check the wall outlet. If still unlit, the power supply may be faulty. |
| Recliner operates intermittently. | Loose cable connections; internal wiring issue in recliner. | Secure all connections. If the problem continues, it may indicate an issue with the recliner's internal wiring or motor. |
8. Specifications
Detailed technical specifications for the MineCtrl TiMOTION TP2 Power Supply:
- Model: TP2-H161-001
- Input: AC 100-240V, 50/60Hz, 1.5A
- Output: DC 29V, 2.5A
- Wattage: 72.5 watts
- Connector Type: 5-Pin Female Plug
- Wire: 22AWG with 4 core wire, approx. 9.9 feet length
- Material: ABS and Copper
- Certifications: UL, CE, FCC Certified
- Special Feature: Built-in Battery Backup (requires 2x 9V batteries, not included)
- Compatible Devices: Recliners and lift chairs from brands such as Pride, Golden, Lazboy, Flexsteel, Ashley, Room to Go, Berkline, Med-lift, Tranquil Ease Lift Chair, Cheers electric sofa, and others using a TiMOTION TP2/TP2P IP20 5-pin power supply.
Image 8.1: Rear view of the power supply unit displaying the product label with specifications and certifications.
9. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact MineCtrl customer service directly. Keep your purchase receipt as proof of purchase.