CYCLEMAX Oil Change Kit for 2022 Yamaha Tracer 9 GT MT-09 User Manual

1. Introduction

This manual provides comprehensive instructions for using the CYCLEMAX Oil Change Kit, specifically designed for the 2022 Yamaha Tracer 9 GT and MT-09 models. Following these guidelines will ensure proper maintenance and optimal performance of your motorcycle's engine.

Kit Contents:

• Four (4) Yamaha LUB-10W40-AP-12 10W40 Performance Quarts of Oil
• One (1) Yamaha 5GH-13440-80-00 Oil Filter
• One (1) 14mm Drain Plug Crush Washer
• One (1) Disposable Funnel

Figure 1: Complete CYCLEMAX Oil Change Kit contents.

2. Safety Information

• Always wear appropriate personal protective equipment, including gloves and eye protection, when handling engine oil.
• Ensure the motorcycle is on a stable, level surface before beginning any maintenance. Use a stand if necessary.
• Allow the engine to cool down before draining oil to prevent burns. However, warm oil drains more thoroughly than cold oil.
• Dispose of used engine oil and filters responsibly according to local environmental regulations. Do not pour used oil down drains or onto the ground.
• Warning: Do not jack up the oil filter. Refer to the oil filter image for this specific warning.

Figure 2: Yamaha Oil Filter (Part No. 5GH-13440-80-00) with important safety markings.

3. Setup and Preparation

Before starting the oil change, gather all necessary tools and ensure a safe working environment.

Required Tools (Not Included):

• Socket wrench and appropriate socket for the drain plug (typically 17mm or 19mm, consult your motorcycle's service manual).
• Oil filter wrench (band-type or cap-type, specific to Yamaha filter size).
• Drain pan with sufficient capacity (at least 4 quarts).
• Clean rags or shop towels.
• Torque wrench (for drain plug and oil filter).

Preparation Steps:

1. Park the motorcycle on a firm, level surface. Use a center stand or paddock stand to keep it upright and stable.
2. Run the engine for a few minutes to warm the oil. This helps the oil drain more completely. Turn off the engine.
3. Place the drain pan directly beneath the engine's oil drain plug.

4. Oil Change Procedure

1. Drain Old Oil: Locate the oil drain plug on the bottom of the engine. Using the appropriate socket wrench, carefully loosen and remove the drain plug. Allow all the old oil to drain completely into the drain pan. This may take several minutes.
2. Replace Drain Plug Washer: Once the oil has drained, clean the drain plug. Replace the old crush washer with the new 14mm crush washer provided in the kit. This ensures a proper seal and prevents leaks. Reinstall the drain plug and tighten it to the manufacturer's specified torque (consult your motorcycle's service manual).
3. Remove Old Oil Filter: Position the drain pan under the oil filter. Use an oil filter wrench to loosen and remove the old oil filter. Be prepared for additional oil to drain out.
4. Prepare New Oil Filter: Take the new Yamaha oil filter (Part No. 5GH-13440-80-00). Apply a thin film of fresh engine oil to the rubber gasket of the new filter. This helps create a good seal and prevents the gasket from sticking.
5. Install New Oil Filter: Screw the new oil filter onto the engine by hand until the gasket makes contact with the engine. Then, tighten it an additional 1/4 to 1/2 turn by hand or with an oil filter wrench, according to the filter manufacturer's instructions or your motorcycle's service manual. Do not overtighten.
6. Add New Engine Oil: Using the provided disposable funnel, carefully pour the new Yamalube 10W-40 engine oil into the engine's oil fill opening. The 2022 Yamaha Tracer 9 GT/MT-09 typically requires approximately 3.0-3.2 liters (3.2-3.4 quarts) during an oil and filter change. Refer to your motorcycle's service manual for the exact capacity.

Figure 3: Yamalube SAE 10W-40 4T Engine Oil.
7. Check Oil Level: After adding the oil, replace the oil fill cap. Start the engine and let it idle for a few minutes to circulate the new oil. Turn off the engine and wait a few minutes for the oil to settle. Check the oil level using the dipstick or sight glass, ensuring it is between the minimum and maximum marks. Add small amounts of oil if necessary.
8. Inspect for Leaks: Visually inspect the drain plug and oil filter for any signs of oil leaks. If leaks are present, re-tighten slightly or re-check installation.
9. Dispose of Used Materials: Properly dispose of the used engine oil and old oil filter at an authorized recycling center.

5. Maintenance

Regular oil changes are crucial for the longevity and performance of your motorcycle's engine. Consult your Yamaha Tracer 9 GT or MT-09 owner's manual for recommended oil change intervals, which typically range from 3,000 to 5,000 miles or annually, whichever comes first.

Always use engine oil that meets the specifications outlined in your motorcycle's owner's manual. The Yamalube 10W-40 oil included in this kit is specifically formulated for Yamaha motorcycles.

6. Troubleshooting

• Oil Leak After Change: Check the tightness of the drain plug and oil filter. Ensure the new crush washer was installed correctly and the oil filter gasket is properly seated and not pinched.
• Incorrect Oil Level: If the oil level is too low, add oil in small increments and re-check. If too high, drain a small amount until the correct level is achieved. Overfilling can cause engine damage.
• Engine Warning Light: If an oil pressure warning light illuminates after an oil change, immediately turn off the engine and investigate. This could indicate a severe leak or incorrect oil level.

7. Specifications

Figure 4: Yamalube 10W-40 oil bottle with detailed product information.

8. Warranty and Support

For any issues or questions regarding your CYCLEMAX Oil Change Kit, please contact CYCLEMAX customer service. Our team of powersports professionals has researched to ensure proper fitment for the listed models.

Specific warranty details for this product are not provided in this manual. Please refer to the product packaging or contact CYCLEMAX directly for warranty information.