Range Oven Broil Heating Element Replaces For Whirlpool RF262LXSQ RF368LXPB RF368LXKQ RF368LXMS RF367LXSB RF262LXSB RF367LXKT WFC150M0EB0 WERE3000SQ0 WERP3000PB4 WERP3000PQ0 WERP3000PQ1 WERP3101SB0

1. Introduction

This manual provides essential information for the installation, operation, and maintenance of your Samoser replacement oven broil heating element. This component is designed to replace original broil heating elements in various Whirlpool, Amana, Roper, and Inglis range models. Please read this manual thoroughly before attempting any installation or maintenance.

2. Safety Information

WARNING: Risk of Electric Shock and Injury.

Always disconnect power to the appliance at the circuit breaker or fuse box before attempting any repairs or installations. Failure to do so can result in serious injury or death.
Wear appropriate personal protective equipment, including gloves and eye protection, during installation.
If you are unsure about any step of the installation process, consult a qualified appliance repair technician.
Ensure the new element is correctly seated and all electrical connections are secure before restoring power.
Keep children and pets away from the work area.

3. Package Contents

Your package should contain the following item:

1x Oven Broil Heating Element

Figure 1: Samoser Oven Broil Heating Element. This image displays the black, serpentine-shaped heating element with two vertical metal support bars and electrical terminals at each end. A small white rectangular component is attached near one terminal.

4. Compatibility

This replacement broil heating element is compatible with a wide range of models from Whirlpool, Amana, Roper, and Inglis. To ensure compatibility, please verify your appliance's model number against the list below. You can often find the model number on a label inside the oven door frame, behind the storage drawer, or on the back of the appliance.

Compatible Models (Partial List):

RF262LXSQ
RF368LXPB
RF368LXKQ
RF368LXMS
RF367LXSB
RF262LXSB
RF367LXKT
WFC150M0EB0
WERE3000SQ0
WERP3000PB4
WERP3000PQ0
WERP3000PQ1
WERP3101SB0
RF368LXMQ0
WFE361LVQ0
WFE361LVQ1
WFC150M0EB1
WFC150M0EB3
RF362LXSB0
RF362LXSB1
RF362LXSQ0
RF362LXSQ1
RF367LXSY0
RF367LXSY1
RF367LXSY2
RF367LXSY3
RF367LXSY4
RF265LXTQ0
RF265LXTQ1
RF265LXTQ2
RF265LXTQ3
RF368LXPQ0
RF368LXPQ1
RF368LXPQ2
RF368LXPQ3
RF368LXPT0
RF368LXPT1
RF368LXPT2
RF368LXPT3
RF368LXPB0
RF368LXPB1
RF368LXPB2
RF368LXPB3
GR465LXLS0
GR465LXLS1
RF462LXSQ0
RF462LXSQ1
RF462LXSQ4
RF367LXKT0
RF262LXSB0
RF262LXSB1
RF262LXSB2
RF262LXSB3
RF262LXSB4
RF262LXSQ0
RF262LXSQ1
RF262LXSQ2
RF262LXSQ3
RF262LXSQ4
RF111PXSQ0
RF111PXSQ1
RF111PXSQ2
RF111PXSQ3
RF367LXSB0
RF367LXSB1
RF367LXSB2
RF367LXSB3
RF367LXSB4
RF367LXSS0
RF367LXSS1
RF367LXSS2
RF367LXSS3
RF367LXSS4
WFE320M0ES0
WFE320M0ES1
RF368LXMS0
RF361PXKQ0
RF361PXKQ1
RF361PXKQ2
WFC130M0AB0
RF362LXTB0
RF362LXTB1
RF362LXTB2
RF362LXTB3
RF368LXKQ0
RF368LXKQ1
RF315PXMQ0
RF364BXEQ0
RF364BXEQ1
RF364BXEQO
RF263LXTT0
RF263LXTT1
RF263LXTT2
RF263LXTT3
RF265LXTB0
RF265LXTB1
RF265LXTB2
RF265LXTB3
RF362LXTS0
RF362LXTS1
RF362LXTS2
RF362LXTS3
MER6600FZ
GFE461LVS0
GFE461LVS1
RF110AXSQ0
RF110AXST2
RF111PXSW3
RF196LXKQ1
RF196LXKT0
RF196LXMB4
RF196LXMQ0
RF196LXMS4
RF196LXMT3
RF196LXMT4
RF199LXHZ0
RF199LXKB0
RF199LXKP1
RF199LXKT0
RF212PXSQ3
RF212PXSQ4
RF214LXTB0
CES366HQ0
GFE471LVS0
GR395LXGB2
GR395LXGQ0
GR395LXGT2
GR395LXGZ0
GR396LXGB1

If your model number is not listed, or if you are unsure about compatibility, please contact the seller for assistance.

5. Installation (Setup)

The following steps outline a general procedure for replacing an oven broil heating element. Specific steps may vary slightly depending on your oven model. Always refer to your appliance's service manual if available.

Disconnect Power: Locate your oven's circuit breaker in your home's electrical panel and turn it OFF. Alternatively, unplug the oven from the wall outlet if accessible. Verify power is off by attempting to turn on the oven light or controls.
Access the Oven Interior: Open the oven door fully.
Remove Mounting Screws: The broil element is typically held in place by two screws at the back of the oven cavity. Use a screwdriver to remove these screws.
Gently Pull Element Forward: Carefully pull the element forward a few inches. This will expose the electrical terminals at the back.
Disconnect Electrical Wires: Note the position of each wire. Using insulated pliers, carefully disconnect the electrical wires from the terminals of the old element. It is advisable to take a photo before disconnecting to aid reassembly.
Remove Old Element: Once wires are disconnected, carefully remove the old broil element from the oven cavity.
Install New Element: Align the terminals of the new Samoser broil heating element with the electrical wires. Connect the wires securely to the corresponding terminals. Ensure a snug fit.
Secure New Element: Push the new element back into its mounting holes at the rear of the oven cavity. Reinstall the mounting screws to secure the element firmly in place.
Restore Power: Close the oven door. Return to your circuit breaker panel and turn the power back ON.
Test Functionality: Turn on the oven's broil function and observe if the element heats up properly and glows red.

6. Operating Instructions

This broil heating element functions as an integral part of your oven's broiling system. Once installed, its operation is controlled by your oven's existing temperature and function settings. Refer to your oven's original user manual for specific instructions on how to use the broil function.

Ensure the oven door is closed or slightly ajar as per your oven's design for broiling. The element will heat up to provide intense top-down heat for browning and searing food.

7. Maintenance

The broil heating element itself requires minimal maintenance. However, proper oven care can extend its lifespan:

Keep Oven Clean: Regularly clean your oven interior to prevent grease and food residue buildup, which can cause smoking and potentially damage heating elements over time.
Avoid Direct Contact: Do not allow food or cookware to directly touch the heating element during operation.
Inspect Periodically: During oven cleaning, visually inspect the element for any signs of damage, such as cracks or severe discoloration.

8. Troubleshooting

If your oven's broil function is not working correctly after element replacement, consider the following:

Problem	Possible Cause	Solution
Element does not heat up.	No power to the oven. Loose electrical connection. Faulty oven control board or thermostat.	Check circuit breaker/fuse. (Disconnect power first!) Verify wires are securely connected to the element terminals. Consult a qualified technician for diagnosis and repair of oven controls.
Element heats unevenly or partially.	Element not fully functional. Incorrect element installed.	Ensure the element is fully seated and not bent. Double-check your oven model number against the compatibility list.
Burning smell after installation.	Residual manufacturing oils burning off. Food debris on element or oven cavity.	Run the oven on broil for 15-30 minutes with good ventilation to burn off oils. Clean the oven interior thoroughly.

For issues not covered here, or if troubleshooting steps do not resolve the problem, it is recommended to contact a professional appliance repair service or the seller for further assistance.

9. Specifications

Attribute	Detail
Brand	Samoser
Part Type	Oven Broil Heating Element
Model Numbers	RF368LXKQ, RF368LXMS (and many others listed in compatibility section)
Replaces For	Whirlpool, Amana, Roper, Inglis Range models
Manufacturer	Samoser
ASIN	B0CLKV4P9H
Date First Available	October 22, 2023

10. Support

For any questions regarding compatibility, installation, or troubleshooting, please contact the seller directly. They are committed to resolving your inquiries within 24 hours.

Please have your appliance's model number and the product's ASIN (B0CLKV4P9H) ready when contacting support.

Samoser RF368LXKQ RF368LXMS

Range Oven Broil Heating Element User Manual