ibealee Tag & Wart Remover Instruction Manual

Product Overview

The ibealee Tag & Wart Remover is a topical solution designed for the removal of skin tags and warts. This product utilizes a natural plant-based formula, aiming for effective and quick results without causing discomfort or scarring.

• Product Type: Skin Tag and Wart Remover
• Capacity: 20 ml
• Application Area: Universal (suitable for various body parts)
• Key Features: Rapid elimination, maximum strength natural formula, painless application, quick healing, non-scarring, non-greasy, fast-drying, easy to apply.

Image: ibealee Tag & Wart Remover product packaging and bottle, showing the included precision tip applicator brush. The bottle contains 20ml of the natural plant extract formula.

Safety Information and Precautions

Before using the ibealee Tag & Wart Remover, please read and understand the following safety guidelines:

1. Topical Use Only: This product is for external application to the skin surface only. Do not ingest orally.
2. Avoid Normal Skin: Apply the product only to the affected area (skin tag or wart). If it comes into contact with normal, healthy skin, wash it off immediately with water.
3. Skin Preparation: If the skin tag or wart has a hard outer layer, gently remove this layer to facilitate product penetration. Exercise caution to avoid thinning the skin too much or causing bleeding.
4. Discontinue if Pain Occurs: If the treated area blackens and you experience slight pain, discontinue use. A scab will form and naturally fall off within approximately three to five days.
5. Keep Out of Reach of Children: Store this product in a location inaccessible to children.
6. Shake Before Use: This product is a liquid. If it has been stored for an extended period, it may appear separated. Shake the bottle well before each use to ensure consistent application.
7. Persistent Scabs: If a black scab forms on the treated area and does not detach naturally after some time, gently remove the scab and reapply the product as directed in the operating instructions.

Setup

The ibealee Tag & Wart Remover requires minimal setup.

• Unscrew the cap, which contains the applicator brush.
• If the product has been stored for a long time, gently shake the bottle to ensure the liquid is well-mixed.

Operating Instructions

Follow these steps for effective application of the ibealee Tag & Wart Remover:

1. Clean the Area: Wash the affected skin area thoroughly with soap and water, then pat it dry completely.
2. Apply the Product: Using the included fiber brush applicator, apply two coats of the liquid directly onto the skin tag or wart. Ensure the entire affected area is covered.
3. Allow Absorption: Wait for the skin to fully absorb the liquid before covering the area or allowing it to come into contact with clothing.
4. Frequency of Use: Apply the product twice daily, once in the morning and once at night.
5. Expected Results: Continue application until the skin tag or wart naturally falls off. In most cases, results are observed within 7 to 10 days. The product is waterproof once absorbed, allowing for normal daily activities.

Image: Step-by-step guide on how to use the ibealee Tag & Wart Remover, showing cleaning, application, absorption, and frequency.

Suitable Application Areas

The ibealee Tag & Wart Remover is formulated for use on various body parts where skin tags and warts may appear, including:

• Hands
• Feet
• Arms
• Legs
• Back
• Neck
• Shoulders
• Chin
• Underarms
• Under Breast
• Forehead

Image: Visual representation of common body areas suitable for applying the ibealee Tag & Wart Remover.

Maintenance

Proper storage ensures the longevity and effectiveness of your ibealee Tag & Wart Remover:

• Store the bottle in a cool, dry place.
• Ensure the cap is tightly secured after each use to prevent evaporation.
• Keep the product out of direct sunlight and extreme temperatures.

Troubleshooting

Refer to these points if you encounter issues during use:

• Product Separation: If the liquid appears separated, shake the bottle vigorously before use. This is normal for liquid products stored over time.
• Hard Skin Layer: If the skin tag or wart has a tough outer layer, gently exfoliate or remove this layer to improve product penetration. Do not cause bleeding.
• Slight Pain/Blackening: If the treated area blackens and you experience mild pain, this indicates the product is working. Discontinue application at this point. The scab will naturally fall off within 3-5 days.
• Scab Not Detaching: If a black scab forms but does not detach naturally after a reasonable period (e.g., after 5-7 days), you may gently remove the scab and reapply the product as per the operating instructions.
• Accidental Contact with Normal Skin: If the product touches healthy skin, immediately wash the area with plenty of water.

Specifications