Introduction
This manual provides essential information for the safe assembly, operation, and maintenance of your GREEN PARTY 56 Inch Gas Fire Pit Table. Please read all instructions carefully before use and retain this manual for future reference.
The GREEN PARTY 56 Inch Gas Fire Pit Table is designed for outdoor use, providing warmth and ambiance with a 50,000 BTU propane flame. It features a durable rattan design, an automatic ignition system, and can also function as an outdoor dining or coffee table when not in use as a fire pit.
Safety Information
WARNING: For Outdoor Use Only. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.
- Ensure the fire pit is placed on a level, non-combustible surface.
- Maintain adequate clearance from combustible materials (e.g., walls, furniture, trees).
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
- Keep children and pets away from the fire pit during operation and while it is cooling down.
- Never leave the fire pit unattended when in use.
- This appliance is CSA certified, ensuring it meets safety standards for gas-fired appliances.
- The unit is equipped with an automatic air cut-off device for enhanced safety, which activates if the table is accidentally overturned.
- Use only propane fuel as specified.
Package Contents
Verify that all components are present and undamaged before assembly. If any parts are missing or damaged, do not attempt to assemble or operate the fire pit. Contact customer support for assistance.
- Fire Pit Table Frame (Rattan and Steel)
- Burner Assembly
- Blue Fire Glass
- Lid for Fire Pit Opening
- Propane Hose and Regulator
- Assembly Hardware (Screws, Washers, etc.)
- Instruction Manual
Setup and Assembly
Assembly typically requires a Phillips screwdriver. Do not fully tighten all screws until the entire unit is assembled to allow for proper alignment.
- Unpack Components: Carefully remove all parts from the packaging. Place them on a soft, clean surface to prevent scratches.
- Assemble Frame: Attach the side panels to the main frame using the provided hardware. Ensure the magnetic door mechanism is correctly oriented.
- Install Burner: Secure the burner assembly into the designated opening on the tabletop.
- Connect Propane Tank: Place a standard 20lb propane tank (not included) inside the designated compartment. Connect the regulator hose to the propane tank valve. Ensure all connections are tight. The magnetic door provides easy access to the propane tank.
- Add Fire Glass: Distribute the blue fire glass evenly over the burner area. Do not obstruct the igniter or burner ports.
- Final Tightening: Once all components are in place and aligned, securely tighten all screws.
Image: Key components including blue fire glass, burner, control panel, and magnetic access door.
Image: Dimensions and magnetic suction design for propane tank access.
Operating Instructions
- Before First Use: Perform a leak test on all gas connections. Apply a soapy water solution to all joints; bubbles indicate a leak. If a leak is detected, tighten connections or replace faulty parts. Do not operate if a leak is present.
- Open Gas Supply: Slowly open the valve on the propane tank.
- Ignite Burner: Push and turn the electronic control knob to the "LOW" position while simultaneously pressing the igniter button. Hold for a few seconds until the flame ignites.
- Adjust Flame: Once ignited, release the igniter button. Rotate the control knob to adjust the flame height to your desired level (Low to High).
- To Turn Off: Turn the control knob to the "OFF" position. Then, close the valve on the propane tank.
Image: Electronic control button for ignition and flame adjustment.
Image: Fire pit in operation during winter.
Image: Fire pit with lid, used as a table in summer.
Maintenance
- Cleaning: Allow the fire pit to cool completely before cleaning. Wipe exterior surfaces with a soft, damp cloth. For stubborn stains, use a mild soap solution. Do not use abrasive cleaners or harsh chemicals.
- Burner Maintenance: Periodically inspect the burner and igniter for debris or insect nests. Clean as necessary to ensure proper gas flow and ignition.
- Fire Glass: The blue fire glass can be rinsed with water and allowed to dry before being placed back in the fire pit.
- Storage: When not in use for extended periods, especially during inclement weather, cover the fire pit with a weather-resistant cover (not included) or store it in a dry, protected area. Disconnect the propane tank.
- Rattan Care: The hand-woven rattan material is weather-resistant. Regular cleaning will help maintain its appearance and longevity.
Image: Detail of the sturdy and durable rattan design.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Burner does not ignite. |
|
|
| Low flame or inconsistent flame. |
|
|
| Gas odor detected. |
|
|
Specifications
- Model: 56 Inch Gas Fire Pit Table
- Brand: GREEN PARTY
- Product Dimensions (L x W x H): 56.7" x 20.8" x 24.8" (144cm x 52.8cm x 63cm)
- Item Weight: 84 Pounds (38.1 kg)
- Heat Output: 50,000 BTU
- Fuel Type: Liquefied Petroleum Gas (Propane)
- Material: Rattan, Steel
- Finish Type: Brushed
- Shape: Long Rectangular
- Certifications: CSA Certified
Warranty Information
Specific warranty details are not provided in the product information. Please refer to the product packaging or contact GREEN PARTY customer support for warranty terms and conditions.
Customer Support
For assistance with assembly, operation, or troubleshooting, please contact GREEN PARTY customer support. Refer to the contact information provided on the product packaging or the official brand website.