1. Product Overview
The ILM Colorful Visor is designed specifically for the E3-12LS helmet model, offering enhanced visibility and a distinctive appearance for day riding. This accessory is engineered to provide high definition transmissivity, ensuring clear vision while meeting specific optical standards for safety and performance.
Figure 1: Side view of the ILM Colorful Visor, highlighting its iridescent finish.
Figure 2: Front view of the ILM Colorful Visor, demonstrating its wide field of vision.
2. Key Features
- Colorful visor optimized for improved safety and aesthetics during day riding.
- Features High Definition Transmissivity for clear and undistorted vision.
- Transmissivity not lower than 85% of visible light, ensuring adequate light transmission.
- Left and Right horizon not lower than 105 degrees, providing a wide peripheral view.
- Up horizon not lower than 7 degrees, maintaining sufficient upward visibility.
3. Setup and Installation
This visor is designed for direct replacement on the ILM E3-12LS helmet. Ensure your helmet is the correct model before attempting installation.
- Preparation: Ensure your helmet is clean and free of debris around the visor mechanism.
- Remove Old Visor (if applicable): Consult your helmet's original manual for specific instructions on removing the existing visor. Typically, this involves pressing release tabs or rotating a lever on each side of the helmet.
- Align New Visor: Carefully align the pivot points of the new ILM Colorful Visor with the corresponding slots on your E3-12LS helmet.
- Secure Visor: Gently press the visor into place until you hear or feel a click on both sides, indicating it is securely latched. Do not force the visor.
- Test Functionality: Once installed, slowly open and close the visor several times to ensure it moves smoothly and locks securely in both open and closed positions. Verify that there are no gaps or loose connections.
If the visor does not fit or operate correctly, re-check the alignment and ensure it is the correct model for your helmet. Refer to your helmet's manual for detailed visor replacement procedures if needed.
4. Operating Instructions
The ILM Colorful Visor is intended for use during daylight conditions. Its high definition transmissivity provides clear vision. Always ensure the visor is clean before riding to maintain optimal visibility.
- Opening and Closing: Use the tab located on the visor to smoothly raise or lower it. Ensure it clicks into place when fully closed to prevent accidental opening during riding.
- Visibility: The colorful tint is designed to enhance comfort and reduce glare in bright daylight. It is not recommended for use in low-light conditions or at night, as it may reduce visibility.
5. Maintenance and Care
Proper care will extend the life and maintain the optical quality of your visor.
- Cleaning: Clean the visor regularly with a soft, lint-free cloth and mild soap and water. Avoid using abrasive cleaners, solvents, or paper towels, as these can scratch the surface or damage the coating.
- Drying: Gently pat dry with a clean, soft cloth. Do not rub vigorously.
- Storage: When not in use, store the helmet with the visor in a protective helmet bag or in a location where it will not be scratched or exposed to extreme temperatures.
- Inspection: Periodically inspect the visor for scratches, cracks, or any damage that might impair visibility. Replace the visor if significant damage is present.
6. Troubleshooting
- Visor does not fit: Ensure your helmet is the ILM E3-12LS model. Double-check the alignment during installation.
- Visor is loose or wobbly: Re-check that both sides of the visor are securely clicked into their pivot points. If the issue persists, inspect the helmet's visor mechanism for wear or damage.
- Visibility is poor: Clean the visor thoroughly. If scratches are present, consider replacing the visor for optimal clarity and safety. Ensure you are using the visor in appropriate daylight conditions.
7. Specifications
| Attribute | Detail |
|---|---|
| Brand | ILM |
| Model | E3-12LS |
| Item Weight | 2.4 ounces |
| Package Dimensions | 9 x 5 x 4 inches |
| Manufacturer Part Number | ILUS-FA-E3-12LS-Visor-Colorful |
| ASIN | B0CHLRZBH6 |
| Date First Available | September 8, 2023 |
8. Warranty and Support
Specific warranty information for the ILM Colorful Visor for E3-12LS is not provided in this manual. For details regarding warranty coverage, returns, or technical support, please contact ILM directly through their official website or the retailer from whom the product was purchased.
You can visit the ILM Store for more information: ILM Official Store
