1. Introduction
This manual provides essential instructions for the safe and effective use of your OUOQNUE 3000ML/min Household Three Inhalation Hydrogen Machine. This device is designed to produce high-purity hydrogen for inhalation, featuring a three-outlet design to accommodate multiple users simultaneously. Please read this manual thoroughly before operating the machine and retain it for future reference.
Figure 1: Front view of the OUOQNUE 3000ML/min Household Three Inhalation Hydrogen Machine, highlighting its vertical design and display.
2. Safety Information
Always observe the following safety precautions to prevent injury or damage to the device:
- Ensure the machine is placed on a stable, level surface away from direct sunlight, heat sources, and flammable materials.
- Use only purified water or distilled water with a TDS (Total Dissolved Solids) level below 3ppm. Using tap water or mineral water can damage the electrolysis module.
- Do not block the ventilation openings on the machine. Ensure adequate air circulation around the unit.
- Keep the machine out of reach of children and pets.
- Do not disassemble or attempt to repair the machine yourself. Contact qualified service personnel for assistance.
- Unplug the power cord before cleaning or performing any maintenance.
- Avoid operating the machine in excessively humid environments.
- If you experience any unusual odors, sounds, or malfunctions, immediately turn off the machine and unplug it.
3. Product Components
Upon unpacking, verify that all the following items are included:
- Hydrogen Machine Unit (x1)
- Nasal Inhaler (x2)
- Transfer Takeover (x2)
- Y-Type Connector (x1)
- Filter Element (x1)
- Power Cord (x1)
- User Manual (x1)
4. Setup Instructions
Follow these steps to set up your hydrogen machine:
- Unpack the Machine: Carefully remove the machine and all accessories from the packaging.
- Placement: Place the machine on a firm, flat, and stable surface. Ensure there is sufficient space around the unit for ventilation. The machine is equipped with wheels for easy movement.
- Fill with Water: Locate the water tank inlet. Fill the tank with purified or distilled water (TDS < 3ppm) up to the maximum fill line. The machine has a 9.6-liter capacity.
- Install Filter Element: Insert the provided filter element according to the instructions in the filter compartment.
- Connect Power: Plug the power cord into the machine's power inlet, then plug the other end into a suitable electrical outlet (220V/50HZ).
- Attach Inhalation Accessories: Connect the nasal inhalers to the transfer takeovers, and then connect the takeovers to the machine's hydrogen outlets. Use the Y-type connector if two users will inhale simultaneously from a single outlet, or connect directly to the three independent outlets.
Figure 2: Rear view of the machine, illustrating the ergonomic handle, wheels for mobility, and the drain switch for water management.
5. Operating Instructions
The machine features a touch screen LCD display for easy control.
- Power On: Press the power button on the control panel. The LCD display will illuminate, showing real-time monitoring information.
- Adjust Flow Rate: The machine offers three adjustable air volume levels: 1500ML/min, 2250ML/min, and 3000ML/min. Use the controls on the touch screen to select your desired flow rate.
- Start Inhalation: Once the desired flow rate is set, place the nasal inhaler comfortably into your nostrils. The machine will begin producing hydrogen.
- Monitor Display: The display shows hydrogen purity (99.99%), current flow rate, and accumulated usage time.
- Intelligent Shutdown: The machine features an intelligent shutdown function. Refer to the display for timer settings or manual shutdown.
- Multiple Users: The three-outlet design allows for independent hydrogen/oxygen output, enabling up to two people to inhale hydrogen simultaneously.
Figure 3: The machine's display panel, illustrating the selectable hydrogen flow rates and real-time operational data.
Figure 4: Close-up view emphasizing the high purity of hydrogen produced by the machine.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your machine.
- Water Replacement: Regularly check the water level and quality. Replace the water in the tank with fresh purified or distilled water as needed, or at least once a week, depending on usage.
- Draining Water: To drain the water, locate the drain switch at the back of the machine (refer to Figure 2). Place a container under the drain outlet and open the switch.
- Filter Element: Replace the filter element periodically as indicated by the machine or based on usage. Refer to the filter element's specific instructions for replacement frequency.
- Cleaning: Wipe the exterior of the machine with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure no water enters the ventilation openings or control panel.
- Storage: If storing the machine for an extended period, drain all water from the tank, clean the unit, and store it in a cool, dry place.
7. Troubleshooting
If you encounter any issues, refer to the following table before contacting customer support:
| Problem | Possible Cause | Solution |
|---|---|---|
| Machine does not power on | Power cord not connected; Power outlet malfunction; Machine fault | Check power cord connection; Test outlet with another device; Contact support |
| No hydrogen production | Insufficient water level; Incorrect water type; Filter element clogged | Refill water tank with purified/distilled water; Replace filter element |
| Low hydrogen flow rate | Selected low flow setting; Clogged filter; Air intake blocked | Adjust flow rate on display; Replace filter; Ensure clear ventilation |
| Unusual noise | Machine not on level surface; Internal component issue | Ensure stable placement; Contact support if noise persists |
| Display not working | Power issue; Display malfunction | Check power; Contact support |
8. Specifications
- Model: 3000ML/min Three Suction
- Rated Voltage: 220V/50HZ
- Rated Power: 800W
- Hydrogen Purity: >99.99%
- Hydrogen Oxygen Ratio: 2000:1000 (H2:O2)
- Shell Material: 6063 Aerospace Aluminum Alloy (Anodized)
- Applicable Raw Water Type: Purified water/distilled water (TDS < 3ppm)
- Electrode Membrane Material: Proton membrane + high-purity platinum coating (American DuPont N117)
- Host Size: 205mm x 380mm x 620mm
- Net Weight: 18kg
- Water Tank Capacity: 9.6 Liters
- Adjustable Flow Rates: 1500ML/min, 2250ML/min, 3000ML/min
Figure 5: Image detailing the use of aviation aluminum alloy for the machine's construction, emphasizing durability.
Figure 6: Detailed view of the machine, showcasing the product label and the high-definition color screen display.
9. Warranty and Support
For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. The manufacturer, OUOQNUE, typically provides a limited warranty against defects in materials and workmanship.
If you require technical assistance, troubleshooting beyond this manual, or have questions regarding your product, please contact OUOQNUE customer support through the contact information provided with your purchase or on the official OUOQNUE website.
Please have your model number (3000ML/min Three Suction) and purchase date ready when contacting support.