Macro 24 LED Ring Light Flash User Manual

1. Introduction

Thank you for choosing the OPTURA HD OPTICS Macro 24 LED Ring Light Flash. This versatile lighting accessory is designed to provide optimal illumination for macro photography and close-up shots. Its flexible arms and adjustable brightness offer precise control over lighting, enhancing the quality of your images. This manual will guide you through the proper setup, operation, and maintenance of your new device.

2. Safety Information

• Do not expose the device to water or excessive humidity.
• Avoid direct eye exposure to the LED lights, as they are very bright.
• Ensure correct battery polarity when inserting batteries.
• Remove batteries if the device will not be used for an extended period.
• Keep out of reach of children.
• Handle the hot shoe mount with care to prevent damage to your camera's hot shoe.

3. Package Contents

Please check the package to ensure all items are present:

• 1 x Macro 24 LED Ring Light Flash Unit
• 1 x Hot Shoe Mount (integrated)

Note: 4x AA batteries are required and are not included in the package.

4. Product Overview

The Macro 24 LED Ring Light Flash features a central control unit with an LCD display and two flexible arms, each terminating in a circular LED light panel. The control unit attaches to your camera's hot shoe.

Figure 1: Macro 24 LED Ring Light Flash Unit. This image shows the main unit with its central control panel and two adjustable LED light arms extending outwards.

Control Unit Components:

• LCD Monitor: Displays battery power, light output power, and current mode.
• PILOT Button: Activates a test flash or modeling light.
• MODE Button: Cycles through different lighting modes.
• LIGHT Button: Toggles between left, right, or both LED panels.
• ON/OFF Button: Powers the unit on or off.
• Directional Buttons (Up/Down/Left/Right): Used for navigation and adjusting settings.
• SET Button: Confirms selections.
• Battery Compartment: Located on the back of the unit.
• Hot Shoe Mount: Located at the bottom of the unit for camera attachment.

5. Setup

5.1 Battery Installation

1. Locate the battery compartment cover on the back of the control unit.
2. Slide the cover open.
3. Insert four (4) AA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. Close the battery compartment cover securely.

5.2 Mounting to Camera

Figure 2: Macro 24 LED Ring Light Flash mounted on a camera. This image illustrates the unit attached to a camera's hot shoe, with the flexible arms positioned for lighting.

1. Ensure your camera is turned off.
2. Slide the hot shoe mount of the Macro 24 LED Ring Light Flash into your camera's hot shoe slot.
3. Secure the unit by tightening the locking wheel or lever on the hot shoe mount (if present) until it is firmly attached. Do not overtighten.
4. Once mounted, you can adjust the flexible arms to position the LED lights as desired for your subject.

6. Operating Instructions

6.1 Power On/Off

• To power on the unit, press and hold the ON/OFF button until the LCD screen illuminates.
• To power off the unit, press and hold the ON/OFF button again until the LCD screen turns off.

6.2 Adjusting Brightness

• Once powered on, use the Up and Down directional buttons to adjust the brightness level. The brightness can be adjusted from -3.0EV to +3.0EV.
• The current brightness level will be displayed on the LCD monitor.

6.3 Light Modes

The unit offers four separate light modes. Press the MODE button to cycle through them:

1. Full Light Mode: Both LED panels illuminate.
2. Left Light Mode: Only the left LED panel illuminates.
3. Right Light Mode: Only the right LED panel illuminates.
4. Flash Mode: The unit acts as a flash, synchronizing with your camera's shutter.

Use the LIGHT button to toggle between illuminating the left panel, right panel, or both panels when not in Flash Mode.

6.4 Using the PILOT Button

Press the PILOT button to activate a test flash or a continuous modeling light, depending on the selected mode. This helps in previewing the lighting effect before taking a picture.

7. Maintenance

• Cleaning: Use a soft, dry cloth to clean the unit. Do not use liquid cleaners or solvents.
• Storage: Store the unit in a cool, dry place away from direct sunlight and extreme temperatures.
• Battery Care: Remove batteries if the unit will not be used for an extended period to prevent leakage.

8. Troubleshooting

9. Specifications

10. Support

For further assistance, technical support, or inquiries regarding your OPTURA HD OPTICS Macro 24 LED Ring Light Flash, please visit the official OPTURA HD OPTICS store on Amazon or contact their customer service directly.

Online Store: OPTURA HD OPTICS Amazon Store