Roziapro HT-87902 Beard Trimmer and Hair Clipper User Manual

1. Important Safety Instructions

Please read all instructions carefully before using this appliance and retain for future reference. Improper use may lead to injury or damage to the product.

• This appliance is intended for household use only.
• Keep the appliance dry. Do not immerse the trimmer in water. The blades can be rinsed under running water, but ensure the charging port remains dry.
• Do not use the appliance with a damaged cord or plug, or if it is not working properly.
• Keep the appliance out of reach of children.
• Do not disassemble the appliance. For service or repair, contact customer support.
• Use only the provided USB charging cable or a compatible USB-C cable. Ensure the charging port is clean and dry before connecting the cable.
• Avoid using the trimmer on irritated skin or open wounds.

2. Product Overview

2.1 Components

• Electric Trimmer Unit
• 4 Cutting Guide Combs (1mm, 2mm, 3mm, 4mm)
• Cleaning Brush
• USB Charger Cable (Type-C)

2.2 Key Features

• Ergonomic Design and Versatility: Features an all-metal retro design for a comfortable grip, suitable for beard trimming, creative styling, sideburns, body hair, and precision trimming.
• Sharp T-Blades: Equipped with ultra-sharp titanium T-shaped blades designed for close-to-skin trimming with zero gaps, ensuring efficient and even hair removal without pulling.
• Battery and Charging: Cordless operation with a rechargeable battery. Provides approximately 90 minutes of working time after a 2-hour fast charge via USB-C. An LED display indicates the remaining battery percentage.
• Motor Performance: Features a powerful motor for stable and efficient operation, while maintaining low noise levels during use.

3. Setup

3.1 Charging the Trimmer

1. Before first use, fully charge the trimmer.
2. Connect the USB-C charging cable to the port at the bottom of the trimmer.
3. Connect the other end of the USB cable to a compatible USB power source (e.g., computer, USB wall adapter, car charger).
4. The LED display will show the charging progress. A full charge typically takes 2 hours.
5. When the LED display shows a number less than 10, it indicates low battery and a reminder to charge.

3.2 Attaching and Removing Guide Combs

1. Ensure the trimmer is turned off before attaching or removing guide combs.
2. Select the desired guide comb (1mm, 2mm, 3mm, or 4mm).
3. Align the guide comb with the trimmer blade and push it down firmly until it clicks securely into place.
4. To remove, gently lift the comb from the back and slide it off the blade.

4. Operating Instructions

4.1 General Trimming

1. Ensure your hair or beard is clean and dry before trimming.
2. Attach the appropriate guide comb for your desired hair length. For closer trims, use no comb or a smaller comb.
3. Turn on the trimmer by pressing the power button.
4. Hold the trimmer with the blades flat against the skin or at a slight angle, moving against the direction of hair growth.
5. Use slow, controlled strokes for an even trim.

4.2 Edging and Detailing

For precise lines and detailing, remove the guide comb. Hold the trimmer with the blade edge perpendicular to the skin and carefully create your desired lines.

5. Maintenance

5.1 Cleaning the Trimmer

1. Turn off the trimmer and disconnect it from any power source.
2. Remove any attached guide comb.
3. Use the provided cleaning brush to remove loose hairs from the blades and the trimmer body.
4. The blades can be rinsed under running water. Ensure the main body and charging port do not get wet.
5. Allow the blades to air dry completely before reattaching combs or storing the trimmer.

5.2 Oiling the Blades

For optimal cutting performance and blade longevity, it is recommended to oil the blades regularly, especially after rinsing. Apply a few drops of clipper oil (not included) to the blades, then turn on the trimmer for a few seconds to distribute the oil. Wipe off any excess oil.

6. Troubleshooting

• Trimmer not turning on: Ensure the battery is charged. If the LED display shows low power, recharge the trimmer.
• Trimmer not charging: Ensure the USB-C cable is securely connected to both the trimmer and the power source. Try a different USB-C cable or power adapter. Check if the charging port is clean and free of debris.
• Poor cutting performance or pulling hair: The blades may need cleaning or oiling. Ensure the blades are free of hair and properly lubricated. The battery might be low; recharge if necessary.
• Guide combs not fitting securely: Ensure the guide comb is correctly aligned with the trimmer blade and pushed down firmly until it clicks into place. If a comb consistently does not fit, it may be damaged.

7. Specifications

8. Warranty and Support

8.1 Warranty Information

This Roziapro product comes with a one-year warranty from the date of purchase. This warranty covers manufacturing defects under normal use. It does not cover damage caused by misuse, accidents, unauthorized modifications, or normal wear and tear.

8.2 Customer Support

If you have any questions, concerns, or require assistance with your Roziapro HT-87902 trimmer, please contact our customer support. Refer to your purchase documentation for specific contact details or visit the official Roziapro website for support information.