Introduction
This instruction manual provides detailed guidance for the safe and proper installation and use of your Stellar Mounts Ultra Slim Tilt TV Wall Mount Bracket. Designed for flat-panel TVs from 32" to 102" with weights up to 165 lbs, this mount offers a low-profile design and tilt adjustment for optimal viewing. Please read all instructions carefully before beginning installation.
Safety Information
- Weight Capacity: Do not exceed the maximum weight capacity of 165 lbs (75 kg).
- Screen Size: This mount is suitable for TVs between 32" and 102".
- Wall Type: Ensure the mounting surface can safely support the combined weight of the mount and your TV. Consult a professional if unsure.
- Tools: Use appropriate tools for installation. Wear safety glasses.
- Assistance: Due to the size and weight of TVs, it is recommended to have at least two people for installation.
- Cable Management: Ensure all cables are routed safely and are not pinched or strained.
Package Contents
Verify that all components are present before beginning installation:
- TV Wall Mount (Wall Plate and TV Brackets)
- Mounting Hardware Kit (screws, anchors, washers)
- Bubble Level
- Instruction Manual
Features
- Low Profile Design: Positions the TV approximately 1.7 inches from the wall for a sleek appearance.
- Tilt Functionality: Allows for a tilt adjustment of 0 to 12 degrees to reduce glare and optimize viewing angles.
- Horizontal Adjustment: Sliding bracket design enables horizontal adjustment of the TV for perfect screen placement after installation.
- Durable Construction: Manufactured from alloy steel for strength and stability.
- Integrated Bubble Level: Includes a bubble level for accurate installation.
- Safety Screws: Features safety screws to secure TV rails to the wall bracket, preventing shifting.
- VESA Compatibility: Supports VESA patterns up to 600x400.
Installation Guide
Follow these steps for proper installation. It is recommended to watch the installation video for visual guidance.
Step 1: Attach Wall Plate to Wall
- Determine the desired mounting height and location on the wall.
- Use the included bubble level to ensure the wall plate is perfectly horizontal. Mark the drilling points.
- Drill pilot holes at the marked locations. The type of drill bit and anchors will depend on your wall construction (wood studs, concrete, brick).
- Secure the wall plate to the wall using the appropriate screws and washers from the hardware kit. Ensure it is firmly attached.
Step 2: Attach Brackets to TV
- Carefully place your TV face down on a soft, clean surface to prevent screen damage.
- Identify the VESA mounting holes on the back of your TV.
- Select the correct size screws and spacers from the hardware kit that fit your TV's mounting holes.
- Attach the two vertical TV brackets to the back of your TV, ensuring they are oriented correctly and securely fastened.
Step 3: Attach TV to Wall Plate
- With assistance, carefully lift the TV and hook the attached TV brackets onto the wall plate.
- Ensure both brackets are properly seated on the wall plate.
- Engage the safety screws or locking mechanisms on the bottom of the TV brackets to secure the TV to the wall plate. This prevents accidental dislodgement.
- Adjust the horizontal position of the TV by sliding it along the wall plate if needed.
Installation Video
For a visual walkthrough of the installation process, please refer to the official Stellar Mounts installation video below:
Video: An official installation guide from Stellar Mounts demonstrating the steps to install the TV wall mount. This video covers attaching the wall plate, securing the TV brackets, and mounting the TV.
Operating Instructions
Tilt Adjustment
This mount allows for a vertical tilt adjustment of your TV from 0 to 12 degrees. To adjust the tilt:
- Locate the tilt adjustment knobs or levers on the side of the TV brackets.
- Loosen the knobs or levers to allow the TV to tilt freely.
- Carefully adjust the TV to your desired viewing angle.
- Once the desired angle is achieved, tighten the knobs or levers to secure the TV in place.
Maintenance
- Regular Checks: Periodically check all screws and connections to ensure they remain tight and secure.
- Cleaning: Clean the mount with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Damage: If any part of the mount appears damaged or worn, discontinue use and contact customer support.
Troubleshooting
- TV Not Level: If the TV appears unlevel after installation, check the wall plate's horizontal alignment using a bubble level. Adjust if necessary by slightly loosening and re-tightening the wall plate screws.
- Mount Feels Loose: Ensure all wall plate screws and TV bracket screws are fully tightened. Verify that the safety screws securing the TV to the wall plate are engaged.
- Difficulty Tilting: Loosen the tilt adjustment knobs or levers sufficiently before attempting to change the tilt angle. Ensure no cables are obstructing the movement.
Specifications
| Specification | Detail |
|---|---|
| Brand | Stellar Mounts |
| Model Number | Tilt Mount for E4FAA75R |
| Mounting Type | Wall Mount |
| Movement Type | Tilt |
| Material | Alloy Steel |
| Color | Black |
| Compatible Devices | Monitor, Television (32" to 102") |
| Maximum Tilt Angle | 12 Degrees |
| Low Profile Distance | 1.7 inches from wall |
| Weight Capacity | 165 lbs (75 kg) |
| Max VESA | 600x400 |
| Item Weight | 6.78 pounds |
| Package Dimensions | 27 x 8.6 x 2.2 inches |
Warranty and Support
For warranty information, please refer to the documentation included with your product or visit the official Stellar Mounts website. If you require technical assistance or have questions regarding installation or operation, please contact the seller or manufacturer directly through their provided support channels.
