1. Introduction
Thank you for choosing the Galaxy Bang 24V 2A Scooter Battery Charger. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your charger. Please read this manual thoroughly before use and retain it for future reference. This charger is designed for electric scooters requiring a 24V 2A power supply with a 3-pin XLR male connector, including Ezip 400, 500, 650, 750, 900, and Mountain Trailz models.
2. Safety Instructions
To ensure safe operation and prevent damage, please observe the following safety precautions:
- Do not disassemble: Never attempt to open or modify the charger. This can lead to electric shock, fire, or damage to the unit.
- Avoid physical damage: Do not crush, puncture, or subject the charger to severe impact.
- Prevent short circuits: Do not short external contacts of the charger.
- Water and fire: Do not expose the charger to water, moisture, or dispose of it in fire.
- Ventilation: Ensure adequate ventilation around the charger during use to prevent overheating.
- Indoor use only: This charger is intended for indoor use in dry conditions.
- Children and pets: Keep the charger out of reach of children and pets.
- Compatibility: Only use this charger with compatible 24V electric scooters that require a 2A current and feature a 3-pin XLR male connector. Verify your scooter's specifications before connecting.
3. Product Overview and Features
The Galaxy Bang 24V 2A Scooter Battery Charger is designed for efficient and safe charging. It features a robust construction and multiple protection mechanisms.
Image 1: The Galaxy Bang 24V 2A Scooter Battery Charger, showing the main adapter unit, AC power cord, and the 3-pin XLR male output connector.
Key Features:
- Fast Charging: Delivers 24V at 2A for efficient battery replenishment.
- Durability: Constructed with an ABS+PC non-combustible shell for high temperature resistance and strength.
- Advanced Heat Dissipation: Built-in aluminum and copper plate ensures faster heat dissipation.
- Intelligent Circuit Protection: Features an intelligent and safe circuit protection chip for accurate voltage control.
- Worldwide Input Voltage: Compatible with 100-240VAC 50/60Hz power sources.
- Charging Indicator Light: Red light indicates charging, green light indicates fully charged.
- Multiple Safety Protections: Includes Over Voltage Protection, Short Circuit Protection, Over Current Protection, Over-Temperature Protection, Cyclic Protection, PTC Protection, Over-Discharge Protection, and Over-Charge Protection.
Image 2: Detailed view of charger components, highlighting the pure copper cable for anti-oxidation and corrosion, an anti-interference ring for stable signal, a durable interface, and a magic tape strap for cable management.
Image 3: A diagram illustrating the various security protections integrated into the charger, including Over-Temperature, Cyclic, PTC, Over-Discharge, Over-Charge, Over-Voltage, Short-Circuit, and Over-Current protections.
4. Setup
Before connecting the charger, it is crucial to confirm compatibility with your electric scooter.
4.1. Confirm Compatibility
Ensure your scooter requires a 24V output voltage and a 2A current. Additionally, verify that your scooter's charging port is compatible with a 3-pin XLR male connector.
Image 4: A visual guide demonstrating how to confirm the correct power adapter by checking the required voltage (24V), current (2A), and the specific 3-pin XLR male connector type, including its 18mm diameter.
4.2. Initial Connection
- Connect the AC power cord to the charger unit.
- Plug the AC power cord into a standard wall outlet (100-240VAC).
- Connect the 3-pin XLR male connector from the charger to your scooter's charging port.
5. Operating Instructions (Charging Process)
Follow these steps to charge your scooter battery:
- Ensure the charger is properly connected to both the power outlet and your scooter's charging port as described in the Setup section.
- The indicator light on the charger will illuminate red, signifying that the battery is currently charging.
- Once the battery is fully charged, the indicator light will turn green.
- Disconnect the charger from the scooter's charging port first, then unplug it from the wall outlet.
Note: Charging times may vary depending on the battery's capacity and its current charge level. Avoid leaving the charger connected for extended periods after the green light appears.
6. Maintenance
Proper maintenance ensures the longevity and optimal performance of your charger.
- Cleaning: Wipe the charger with a dry, soft cloth. Do not use liquid cleaners or solvents.
- Storage: Store the charger in a cool, dry place away from direct sunlight and extreme temperatures when not in use.
- Cable Care: Avoid bending or kinking the cables excessively. Use the integrated magic tape strap for neat storage.
- Inspection: Periodically inspect the charger and cables for any signs of damage. If damage is observed, discontinue use immediately.
7. Troubleshooting
If you encounter issues with your charger, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Charger indicator light does not turn on. | No power from outlet; loose connection; faulty charger. | Check wall outlet with another device; ensure all connections are secure; if problem persists, contact support. |
| Indicator light remains red after extended charging. | Battery not fully charged; battery issue; charger issue. | Allow more time for charging; test with another compatible battery if possible; contact support if issue persists. |
| Charger gets excessively hot. | Poor ventilation; internal fault. | Ensure charger is in a well-ventilated area; discontinue use immediately and contact support if overheating is severe. |
| Scooter not charging. | Incorrect charger; scooter charging port issue; battery issue. | Verify charger compatibility (24V 2A, 3-pin XLR); inspect scooter charging port for damage; consult scooter manual or technician. |
If troubleshooting steps do not resolve the issue, please contact customer support.
8. Specifications
Detailed technical specifications for the Galaxy Bang 24V 2A Scooter Battery Charger:
- Model: KT60W190342B3
- Input Voltage: 100-240VAC, 50/60Hz
- Output Voltage: 24V
- Output Current: 2A
- Output Power: 48W
- Connector Type: 3-pin XLR Male
- Safety Features: Over Voltage Protection, Short Circuit Protection, Over Current Protection, Over-Temperature Protection, Cyclic Protection, PTC Protection, Over-Discharge Protection, Over-Charge Protection.
- Dimensions (Adapter Unit): Approximately 6 x 3 x 2 inches (15.2 x 7.6 x 5.1 cm)
- Item Weight: 8 ounces (227 grams)
- Cable Length: Total length approximately 3.9ft (1.2m) for AC input, 3.7ft (1.15m) for DC output.
Image 5: A diagram illustrating the physical dimensions of the AC adapter unit and the lengths of the input and output cables, including the 0.68-inch diameter of the XLR connector.
9. Warranty and Support
Warranty: This product comes with a 12-month warranty for exchange from the date of purchase.
Returns: You may return the product for any reason within 30 days of the purchase date.
Customer Support: If you have any questions regarding your Galaxy Bang electric scooter charger, please do not hesitate to contact us. We are committed to providing a response within 24 hours to assist you.
