1. Introduction
This manual provides essential instructions for the safe installation, operation, and maintenance of your Troy Lighting Willard F9922-PBR/SBK 2-Light Pendant. Please read all instructions carefully before beginning installation and retain this manual for future reference.
Important Safety Information
- Always turn off the main power supply at the circuit breaker before installing, servicing, or cleaning the fixture.
- Consult a qualified electrician if you are unsure about the installation process.
- All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC).
- Use only the specified bulb type and wattage to avoid fire hazards.
- Do not connect this fixture to an ungrounded electrical system.
- This fixture is rated for damp locations. Do not install in areas with direct water exposure.
2. Package Contents
Carefully unpack your fixture and inspect all components for damage. Keep all packaging materials until you are certain all parts are present and in good condition. The package should contain:
- Pendant Fixture Assembly
- Mounting Hardware Kit (crossbar, mounting screws, wire nuts)
- Glass Globes (2)
- Instruction Manual
3. Setup and Installation
Professional installation by a licensed electrician is recommended.
Pre-Installation Steps
- Turn off power: Locate the circuit breaker that supplies power to the light fixture outlet box and turn it off.
- Prepare the area: Clear the work area and ensure you have all necessary tools (screwdriver, wire strippers, electrical tape, ladder).
- Identify wires: In the outlet box, identify the supply wires: typically black (hot), white (neutral), and bare copper or green (ground).
Mounting and Wiring
- Attach mounting bracket: Secure the fixture's mounting crossbar to the outlet box using the provided screws. Ensure it is firmly attached.
- Adjust hanging height: Determine the desired hanging height for the pendant. Adjust the stem length as needed.
- Make electrical connections:
- Connect the fixture's bare copper or green ground wire to the supply ground wire using a wire nut.
- Connect the fixture's white (neutral) wire to the supply white (neutral) wire using a wire nut.
- Connect the fixture's black (hot) wire to the supply black (hot) wire using a wire nut.
- Ensure all connections are secure and insulated with electrical tape if necessary.
- Tuck wires: Carefully tuck all wires into the outlet box.
- Secure canopy: Attach the fixture canopy to the mounting bracket, securing it with the provided screws or decorative nuts.
- Install glass globes: Carefully attach the two opal glass globes to the fixture according to the design.
Image 1: Troy Lighting Willard 2-Light Pendant (Model F9922-PBR/SBK) with Patina Brass finish and opal glass globes.
4. Operating Instructions
Once installation is complete and verified by a qualified professional, you can operate your pendant light.
- Install bulbs: Screw in two incandescent bulbs (not included) into the sockets. Ensure the wattage does not exceed 60 Watts per bulb.
- Restore power: Turn the main power supply back on at the circuit breaker.
- Activate light: Use your wall switch to turn the pendant light on and off.
5. Maintenance
Regular maintenance will help preserve the appearance and functionality of your fixture.
Cleaning
- Always turn off power and allow the fixture to cool before cleaning.
- Wipe the fixture with a soft, dry cloth.
- Do not use abrasive cleaners, solvents, or polishes as they may damage the finish.
- Clean glass globes with a mild glass cleaner and a soft cloth.
Bulb Replacement
- Turn off power at the circuit breaker and allow bulbs to cool completely.
- Carefully unscrew the old bulb from the socket.
- Screw in a new incandescent bulb, ensuring it does not exceed 60 Watts.
- Restore power.
6. Troubleshooting
If your fixture is not functioning correctly, refer to the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check the circuit breaker and wall switch. Ensure power is on. |
| Bulb is faulty or loose. | Replace the bulb or tighten it securely. | |
| Incorrect wiring. | Verify all electrical connections are correct and secure. Consult a qualified electrician. | |
| Light flickers. | Loose bulb or wiring connection. | Tighten the bulb. Check wiring connections for security. |
| Incorrect dimmer switch. | Ensure the dimmer switch is compatible with incandescent bulbs. |
If troubleshooting steps do not resolve the issue, contact customer support or a qualified electrician.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Troy Lighting |
| Model Number | F9922-PBR/SBK |
| Collection | Willard |
| Dimensions (L x W x H) | 7.75" x 9.25" x 25" |
| Material | Brass, Steel, Glass |
| Finish | Patina Brass, Soft Black |
| Shade Material | Opal Glass |
| Number of Lights | 2 |
| Lamping Type | Incandescent |
| Max Wattage (per bulb) | 60 Watts |
| Voltage | 120 Volts |
| Moisture Rating | Damp Rated |
| Item Weight | 10.14 pounds |
| UPC | 782042470194 |
| Assembly Required | Yes |
8. Warranty Information
This Troy Lighting product is covered by a manufacturer's warranty. For specific details regarding warranty coverage, terms, and conditions, please refer to the documentation provided with your purchase or visit the official Troy Lighting website. Keep your proof of purchase for warranty claims.
9. Customer Support
If you have any questions, require assistance with installation, or need to report a missing or damaged part, please contact Troy Lighting customer service. You can typically find contact information on the official Troy Lighting website or on your purchase receipt.
For more information, visit: Troy Lighting Store on Amazon
