Product Overview
The Artika Vester LED Vanity Light (model VAN-VE-CR) is a modern, chrome-finished lighting fixture designed for indoor damp locations, such as bathrooms. It features integrated LED technology, offering 1900 lumens of bright, 3000K warm white light with a long lifespan of 50,000 hours. This fixture is dimmable and controlled via a remote.
Image: Front view of the Artika Vester LED Vanity Light, showcasing its chrome finish and linear design.
Setup and Installation
This section provides general guidelines for installing the Artika Vester LED Vanity Light. Professional installation is recommended. Always ensure the power supply is turned off at the circuit breaker before beginning any electrical work.
Required Tools (Not Included):
- Screwdriver (Phillips and Flathead)
- Wire Strippers
- Electrical Tape
- Safety Glasses
- Voltage Tester
Installation Steps:
- Turn off Power: Locate the circuit breaker controlling the light fixture's power supply and switch it to the OFF position. Verify power is off using a voltage tester.
- Remove Old Fixture: Carefully remove any existing light fixture from the wall. Disconnect all wires and remove the mounting bracket.
- Install Mounting Bracket: Attach the new mounting bracket (supplied with the Vester light) to the electrical junction box on the wall using the provided screws. Ensure it is securely fastened.
- Wire Connections: Connect the electrical wires from the fixture to the corresponding wires from the junction box. Typically, connect the black wire (live) from the fixture to the black wire from the junction box, the white wire (neutral) from the fixture to the white wire from the junction box, and the ground wire (bare copper or green) from the fixture to the ground wire from the junction box. Secure connections with wire nuts and electrical tape.
- Mount the Fixture: Carefully align the Vester LED Vanity Light with the mounting bracket and secure it in place using the provided screws. Ensure the fixture is flush against the wall and stable.
- Restore Power: Once the fixture is securely installed, turn the power back on at the circuit breaker.
No specific installation videos are available for this product. Please refer to the written instructions and consult a qualified electrician if you are unsure about any steps.
Operating Instructions
The Artika Vester LED Vanity Light is designed for simple operation using its included remote control.
Remote Control Functions:
- Power Button: Press to turn the light ON or OFF.
- Dimming Buttons: Use the '+' and '-' buttons to increase or decrease the brightness level of the light. The Vester light is fully dimmable.
Ensure the remote control has working batteries and is pointed towards the light fixture for optimal response. The light operates at a fixed color temperature of 3000K (warm white).
Maintenance
The Artika Vester LED Vanity Light requires minimal maintenance due to its durable construction and long-lasting integrated LED components.
Cleaning:
- Always turn off the power to the fixture at the circuit breaker before cleaning.
- Use a soft, dry, or slightly damp cloth to wipe the exterior surfaces of the fixture.
- Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or electrical components.
- Do not spray cleaning solutions directly onto the fixture.
LED Components:
The LED light source in this fixture is integrated and not user-replaceable. With an average lifespan of 50,000 hours, regular replacement is not anticipated.
Troubleshooting
If you encounter issues with your Artika Vester LED Vanity Light, refer to the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture. | Check the circuit breaker and wall switch. Ensure power is ON. |
| Loose wire connections. | Turn off power at the breaker. Inspect wire connections inside the junction box and re-secure if loose. | |
| Remote control battery is dead. | Replace the battery in the remote control. | |
| Light flickers or dims unexpectedly. | Incompatible dimmer switch. | Ensure you are using an LED-compatible dimmer switch. Consult a qualified electrician. |
| Loose wire connections. | Turn off power at the breaker. Inspect wire connections and re-secure. | |
| Remote control not responding. | Remote battery is dead or low. | Replace the remote control battery. |
| Obstruction between remote and fixture. | Ensure a clear line of sight between the remote and the light fixture. |
If these steps do not resolve the issue, please contact customer support.
Specifications
| Brand | Artika |
| Model Number | VAN-VE-CR |
| Product Dimensions | 27" L x 4.4" W x 4.4" H |
| Wattage | 21 Watts |
| Voltage | 120 Volts |
| Brightness | 1900 Lumens |
| Color Temperature (CCT) | 3000K (Warm White) |
| Color Rendering Index (CRI) | 80 |
| Average Life | 50,000 Hours |
| Material | Alloy Steel, Plastic |
| Mounting Type | Wall Mount |
| Control Method | Remote Control |
| Location Rating | Damp Location (Indoor) |
| UPC | 846979036677 |
Warranty Information
Specific warranty details for the Artika Vester LED Vanity Light (VAN-VE-CR) are typically provided with the product packaging or available on the manufacturer's official website. Please retain your proof of purchase for warranty claims. For detailed information regarding warranty coverage, terms, and conditions, please refer to the documentation included with your product or visit the Artika website.
Support
For further assistance, technical support, or to inquire about replacement parts, please contact Artika customer service. You can typically find contact information on the manufacturer's website or within the product packaging.
You may also visit the official Artika store on Amazon for product information and updates: Artika Store on Amazon
