BANDAI SPIRITS 2648701

Instruction Manual

BANDAI SPIRITS 30MM 1/144 Extended Armament Vehicle Multiple Legs Mecha ver. (Model: 2648701)

Introduction

This manual provides detailed instructions for assembling and operating your BANDAI SPIRITS 30MM 1/144 Extended Armament Vehicle Multiple Legs Mecha ver. model kit. Please read all instructions carefully before beginning assembly to ensure proper construction and functionality. This kit is designed for hobbyists and requires assembly.

Package Contents

Before starting, verify that all components are present. The package should contain:

  • Main body kit vehicle x 1
  • Sticker sheet x 1

Refer to the image below for an overview of the kit components.

Exploded view of the 30MM Multiple Legs Mecha ver. kit components, showing the main body, individual leg segments, and weapon parts.

Image: Exploded view of the kit components, illustrating the various parts included for assembly.

Setup and Assembly

Follow these steps to assemble your model kit:

  1. Part Identification: Carefully remove all parts from the runners. Use a hobby knife or nippers for clean cuts. Refer to the included diagram for part identification.
  2. Leg Assembly: Assemble each leg segment. The leg parts are designed for flexible movement from the base to the toe. Ensure all joints are securely connected but allow for articulation.
  3. Main Body Assembly: Construct the central body unit. Pay attention to the orientation of parts as indicated in the instructions.
  4. Attach Legs: Connect the assembled leg units to the main body. There are multiple connection points for varied configurations.
  5. Weapon Assembly: Assemble the gun barrel components.
  6. Weapon Attachment: Attach the gun barrel to the designated port on the back of the main body. The gun barrel can also be attached to a front leg for alternative configurations.
  7. Apply Stickers: Use the provided sticker sheet to add markings as desired.

An assembled view of the model is shown below:

Front-top view of the fully assembled 30MM Multiple Legs Mecha ver. model, showcasing its multi-legged design and twin cannons.

Image: The fully assembled Multiple Legs Mecha ver. model.

Operating and Customization

The 30MM Extended Armament Vehicle is designed for high poseability and customization.

  • Articulation: Each joint from the base to the tip of the legs is posable, allowing for a wide range of dynamic stances.
  • Weapon Positioning: The gun barrel on the back can be repositioned and attached to a front leg, offering different combat configurations.
Close-up view of the twin cannons, with Japanese text indicating they can be attached to the front legs.

Image: Detail showing the gun barrels and their alternative attachment points on the front legs.

  • Modular Design: This model is part of the 30MM (30 Minutes Missions) series, known for its modularity. Parts can be disassembled and used as customizing components for other 30MM kits.
  • Extension: Multiple sets of this item can be combined to create larger, more complex multi-legged mechanical units.
An image showing how multiple units of the Multiple Legs Mecha ver. can be combined to create an extended, longer multi-legged vehicle, alongside a 30MS figure for scale.

Image: Example of combining multiple units for an extended configuration, demonstrating the customization potential.

Maintenance

To ensure the longevity and appearance of your model:

  • Cleaning: Dust the model regularly with a soft brush or compressed air. Avoid using harsh chemicals or abrasive materials.
  • Storage: Store the model in a cool, dry place away from direct sunlight to prevent discoloration or material degradation.
  • Handling: Handle the model by its sturdy parts. Avoid excessive force on joints or thin components to prevent breakage.

Troubleshooting

If you encounter any issues during assembly or operation, consider the following:

  • Parts Not Fitting: Ensure you are using the correct parts for each step. Double-check the instruction diagrams. Sometimes, a small amount of plastic flash may need to be trimmed from the part.
  • Loose Joints: If a joint feels too loose, a thin layer of clear nail polish or hobby cement applied to the ball joint (and allowed to dry) can increase friction.
  • Missing Parts: If you believe a part is genuinely missing, please contact BANDAI SPIRITS customer support with your product details.

Specifications

BrandBANDAI SPIRITS
Model Number2648701
Scale1/144
MaterialPlastic
Product Dimensions7.09 x 9.06 x 2.36 inches (L x W x H)
Item Weight6 ounces
Included ComponentsMain body kit vehicle x 1, Sticker sheet x 1

Warranty and Support

This product is a model kit and typically does not come with a traditional warranty for assembled parts. However, if you encounter issues such as manufacturing defects or missing components upon initial inspection, please contact BANDAI SPIRITS customer support directly. Keep your purchase receipt and product packaging for reference.

For further assistance or inquiries, please visit the official BANDAI SPIRITS website or contact their customer service department.

© 2019 BANDAI SPIRITS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.