1. Introduction
This instruction manual provides comprehensive guidance for the safe and effective installation, operation, and maintenance of your Karjoefar 100W LED Flood Light Outdoor. Please read this manual thoroughly before use and retain it for future reference.
2. Safety Information
- Always disconnect power before installation or servicing.
- Ensure the power source voltage matches the product's requirements (110-120V AC).
- Do not look directly into the LED light source when illuminated.
- Keep away from flammable materials.
- Installation should be performed by a qualified electrician if you are unsure.
- The product may become hot during operation. Avoid direct contact with the housing.
3. Product Overview
The Karjoefar 100W LED Flood Light is designed for outdoor use, providing bright and efficient illumination. Key features include:
- High Brightness: 100W, 10000 lumens, 6500K Daylight White.
- Wide Coverage: 120° beam angle for extensive illumination.
- Durable Design: IP66 waterproof rating and die-cast aluminum housing for outdoor resilience.
- Efficient Cooling: Fin-type heat sink for optimal heat dissipation and extended lifespan.
- Adjustable Bracket: 180° adjustable U-shape bracket for flexible positioning.
- Plug and Play: Equipped with a 59-inch cable and plug for easy installation.
Figure 3.1: Karjoefar 100W LED Flood Lights illuminating an outdoor area.
Package Contents:
- 2 x Karjoefar 100W LED Flood Light
- 1 x Instruction Manual
4. Setup and Installation
The Karjoefar LED Flood Light is designed for easy installation. Follow these steps for proper setup:
- Choose Location: Select a suitable outdoor location for mounting, such as a wall, ceiling, or ground. Ensure the surface is stable and can support the weight of the floodlight.
- Adjust Bracket: The U-shape bracket can be adjusted 180 degrees. Loosen the screws on the sides of the bracket, position the light at the desired angle, and then tighten the screws securely.
Figure 4.1: Adjusting the flood light bracket for optimal angle.
- Mounting:
- Wall Mounting: Mark the drilling points using the bracket as a template. Drill holes, insert appropriate anchors (if needed), and secure the floodlight to the wall using screws.
- Ceiling Mounting: Follow similar steps as wall mounting, ensuring the ceiling can support the fixture.
- Ground Mounting: The bracket can also be used to secure the light to a flat surface or a compatible tripod (not included).
Figure 4.2: Various installation methods for the flood light.
- Connect Power: Plug the 59-inch power cable into a standard 110-120V AC outdoor power outlet. Ensure the outlet is protected from water.
Figure 4.3: Power cord and plug for easy connection.
Note: This flood light does not include a dusk-to-dawn sensor, motion sensor, switch, or remote control. It operates when plugged into a live power source.
5. Operating Instructions
Operating the Karjoefar LED Flood Light is straightforward:
- Once properly installed and plugged into a power source, the flood light will illuminate.
- To turn the light on or off, use the switch on the power outlet or an external timer (not included) connected to the power source.
- Adjust the angle of the light as needed by loosening the bracket screws, repositioning, and re-tightening.
Figure 5.1: Flood light providing wide illumination on a porch.
6. Maintenance
Minimal maintenance is required for your LED flood light:
- Cleaning: Ensure the power is disconnected before cleaning. Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Inspection: Periodically check the power cord and plug for any signs of damage. Inspect mounting hardware for tightness.
- Heat Dissipation: The fin-type heat sink is designed for efficient cooling. Ensure it is not obstructed by debris or insulation to maintain optimal performance and lifespan.
Figure 6.1: Heat dissipation mechanism of the flood light.
7. Troubleshooting
If you encounter issues with your flood light, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Faulty outlet. Damaged cable/plug. | Check if the plug is securely inserted. Test the outlet with another device. Inspect the cable and plug for damage. If damaged, contact customer support. |
| Light flickers. | Unstable power supply. Loose connection. | Ensure the power supply is stable. Check all connections for tightness. |
| Light is dim. | Dirt or debris on the lens. | Clean the lens with a soft, damp cloth (ensure power is off). |
If the problem persists after trying these solutions, please contact customer service.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Karjoefar |
| Model Name | Flood Light 100W (AVUSFL-01) |
| Wattage | 100 Watts |
| Brightness | 10000 Lumens |
| Light Color | 6500K Daylight White |
| Voltage | 110-120 Volts (AC) |
| Beam Angle | 120° |
| Waterproof Rating | IP66 |
| Material | Aluminum, Polycarbonate |
| Product Dimensions | 9.8"L x 4"W x 0.98"H |
| Item Weight | 1.76 pounds |
| Average Life | 30,000 Hours |
| Power Source | Corded Electric (59-inch cable with plug) |
| Installation Type | Wall Mount, Ceiling Mount, Ground Mount |
Figure 8.1: Key specifications and dimensions of the flood light.
9. Warranty and Customer Support
Karjoefar is committed to providing high-quality products and excellent customer service.
- Warranty: This product comes with a 1-year warranty from the date of purchase.
- Money-Back Guarantee: A 60-day money-back guarantee is offered for quality-related issues.
- Technical Support: 24-hour technical support is available to assist with any questions or issues you may encounter.
For warranty claims, technical assistance, or any other inquiries, please contact Karjoefar customer service through the platform where you purchased the product.