Introduction
Thank you for choosing the Rocketfish Tilting TV Wall Mount. This manual provides detailed instructions for the safe and proper installation, operation, and maintenance of your new TV wall mount. Designed for 32-inch to 90-inch flat-panel televisions, this mount offers a secure and low-profile solution with convenient fingertip tilt adjustment for optimal viewing angles. Please read this manual thoroughly before beginning installation and retain it for future reference.
Image: Rocketfish Tilting TV Wall Mount, front view.
Safety Information
Improper installation or use of this product can result in serious injury or damage. Please observe the following safety precautions:
- Read all instructions: Ensure you understand all instructions and warnings before installation. If you have any questions, contact customer support.
- Weight Capacity: Do not exceed the maximum weight capacity of 130 lbs (59 kg). This mount is designed for TVs between 32 and 90 inches.
- Wall Type: This mount is designed for installation on wood stud walls or solid concrete/brick walls. Do not install on drywall alone.
- Professional Installation: If you are unsure about your ability to install this mount safely, seek assistance from a qualified professional.
- Component Check: Before installation, verify that all components are present and undamaged. Do not use damaged parts.
- Avoid Over-tightening: Do not over-tighten screws, as this may cause damage to the mount or your TV.
- Children: Keep children away from the installation area.
Package Contents
Carefully unpack the box and ensure all items listed below are present and undamaged. If any parts are missing or damaged, do not attempt to install the mount. Contact Rocketfish customer support for assistance.
- Wall Plate Assembly
- TV Bracket Arms (2)
- Hardware Kit (various screws, washers, spacers, anchors)
- Instruction Manual
Setup and Installation
Tools Required (Not Included)
- Phillips Head Screwdriver
- Drill with appropriate drill bits (wood or masonry)
- Stud Finder (for wood stud installation)
- Level
- Pencil
- Tape Measure
- Hammer (for concrete anchors)
Pre-Installation Checklist
- TV Compatibility: Verify your TV's VESA mounting pattern and weight are within the mount's specifications (32"-90" and up to 130 lbs).
- Wall Structure: Ensure the wall can safely support the combined weight of the mount and your TV.
- Location: Choose a mounting location free from electrical wires, water pipes, or other hazards.
Image: Visual representation of TV compatibility for the mount.
Step-by-Step Installation
- Locate Wall Studs (Wood Stud Installation): Use a stud finder to locate the edges and center of two adjacent wood studs. Mark the center of the studs at the desired height for the top of your TV. Ensure the marks are level.
- Mark Drilling Points: Hold the wall plate against the wall, aligning its center with your marked stud centers. Use a level to ensure the wall plate is perfectly horizontal. Mark the drilling points through the holes on the wall plate.
- Drill Pilot Holes: For wood studs, drill pilot holes using a 7/32" (5.5 mm) drill bit to a depth of 2.2" (55 mm). For concrete/brick walls, use a 3/8" (10 mm) masonry drill bit to a depth of 2.4" (60 mm) and insert concrete anchors.
- Attach Wall Plate: Secure the wall plate to the wall using the provided lag bolts and washers. Tighten the bolts firmly but do not over-tighten.
- Attach TV Brackets to TV: Carefully place your TV face down on a soft, clean surface. Attach the two TV bracket arms to the back of your TV using the appropriate screws, washers, and spacers from the hardware kit. Ensure the brackets are centered and securely fastened.
- Hang TV on Wall Plate: With assistance, carefully lift the TV and hook the TV bracket arms onto the top edge of the wall plate. Gently lower the TV until the brackets engage with the wall plate.
- Secure TV: Locate the locking screws or mechanisms on the bottom of the TV bracket arms. Tighten these screws to secure the TV to the wall plate, preventing accidental dislodgement.
- Adjust Tilt: Loosen the tilt tension knob(s) on the mount (if applicable) to adjust the TV to your desired viewing angle. Once set, tighten the knob(s) to secure the tilt position.
Operating the Tilt Feature
The Rocketfish Tilting TV Wall Mount features fingertip tilt technology, allowing you to easily adjust your TV's vertical viewing angle. To tilt your TV:
- Loosen Tension: Locate the tilt tension knob(s) on the side or bottom of the TV bracket arms. Turn the knob(s) counter-clockwise slightly to loosen the tension.
- Adjust Angle: Gently push or pull the bottom of your TV to achieve the desired upward or downward tilt angle.
- Secure Position: Once the desired angle is achieved, turn the tilt tension knob(s) clockwise to tighten and secure the TV in place. Ensure the TV is stable before releasing it.
Image: Close-up of the tilt tension knob for adjustment.
Maintenance
Regular maintenance helps ensure the longevity and safe operation of your TV wall mount.
- Cleaning: Wipe the mount with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the finish.
- Periodic Checks: Periodically check all screws and connections to ensure they remain tight and secure. If any looseness is detected, re-tighten them immediately.
- Damage Inspection: Inspect the mount for any signs of damage or wear. If any damage is found, do not use the mount and contact customer support.
Troubleshooting
If you encounter issues with your Rocketfish TV wall mount, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level. | Wall plate not level during installation. | Remove TV, loosen wall plate screws, adjust with a level, and re-tighten. |
| Mount feels loose on the wall. | Lag bolts not fully tightened or improper wall anchors used. | Ensure lag bolts are securely tightened into studs/anchors. Verify correct anchors for wall type. |
| TV tilt is too stiff or too loose. | Tilt tension knob needs adjustment. | Adjust the tilt tension knob(s) as described in the "Operating the Tilt Feature" section. |
| TV does not fit the mount. | Incorrect VESA pattern or TV weight exceeds capacity. | Verify your TV's VESA pattern and weight against the mount's specifications. This mount supports 32"-90" TVs up to 130 lbs. |
If the problem persists or is not listed here, please contact Rocketfish customer support.
Specifications
| Feature | Specification |
|---|---|
| Brand | Rocketfish |
| Model Number | RF-TVMLPT03V3 |
| Mounting Type | Wall Mount |
| Movement Type | Tilt |
| Compatible TV Sizes | 32 - 90 Inches |
| Maximum Weight Capacity | 130 lbs (59 kg) |
| Material | Either Aluminum, Stainless Steel, or Alloy Steel |
| Product Dimensions | 2 x 26.49 x 17.4 inches |
| Item Weight | 6 pounds |
| Low Profile Design | Positions TV 1.9" from the wall |
Warranty and Support
Rocketfish products are designed for quality and reliability. For specific warranty information, please refer to the warranty card included with your product or visit the official Rocketfish website. If you require technical assistance, have questions about installation, or need to report missing/damaged parts, please contact Rocketfish customer support. Have your product model number (RF-TVMLPT03V3) and purchase information ready when contacting support.
You can often find support contact information on the Rocketfish official website or through the retailer where you purchased the product.
