Dynasty PROAUDIO WSA-5RP-PLUS Wireless Surround Sound Speaker Kit User Manual

Introduction

Image: The Dynasty PROAUDIO WSA-5RP-PLUS Wireless Surround Sound Speaker Kit, showing the stacked Transmitter and Receiver units from the front with their power switches and status LEDs.

This manual provides detailed instructions for the installation, operation, and maintenance of your Dynasty PROAUDIO WSA-5RP-PLUS Wireless Surround Sound Speaker Kit. This system is designed to convert your passive rear surround speakers into a wireless setup, eliminating the need for long speaker cables. It features dual-band wireless technology for stable audio transmission and a built-in Class D amplifier to power your speakers.

Package Contents

Please verify that all items listed below are included in your package. If any items are missing or damaged, please contact customer support.

Image: The image displays the complete package contents, including the transmitter, receiver, antennas, power adapters, speaker wires, and user manual, laid out next to the product box.

• 1 x WSA-5RP-PLUS Wireless Transmitter (TX)
• 1 x WSA-5RP-PLUS Wireless Receiver (RX)
• 2 x Wireless Antennas
• 2 x Speaker Wires
• 1 x 9V Power Adapter (for Transmitter)
• 1 x Power Cord (for Receiver)
• 1 x User Manual (this document)

Product Overview

The Dynasty PROAUDIO WSA-5RP-PLUS system consists of two main units: a Transmitter (TX) and a Receiver (RX).

Transmitter (TX) Unit

Image: Rear panel view of both the Transmitter (top) and Receiver (bottom) units, showing all input and output ports, antennas, and controls.

The Transmitter unit sends audio signals wirelessly to the Receiver. It features:

• Antenna Port: For connecting the wireless antenna.
• Speaker Level Input: Connects to the speaker outputs of your A/V receiver or amplifier.
• Stereo RCA Input (Line In): Connects to RCA line-level outputs from your A/V receiver or preamp.
• Subwoofer Input: For connecting a subwoofer signal from your A/V receiver.
• DC 9V Input: For connecting the provided 9V power adapter.
• ATT Switch: Attenuation switch to adjust input sensitivity (0, -6, -12 dB).
• Power Switch: On/Off toggle.
• Status LED: Indicates power and connection status.

Receiver (RX) Unit

The Receiver unit receives wireless audio signals from the Transmitter and amplifies them for your passive speakers. It features:

• Antenna Port: For connecting the wireless antenna.
• Speaker Output Terminals: Connects to your passive rear surround speakers (L+/L- and R+/R-). Supports banana plugs or bare wire.
• Subwoofer Output: For connecting to an active subwoofer or subwoofer amplifier.
• Mode Switch: Selects between Stereo, Bridge, or Mono output modes.
• Volume Knob: Adjusts the output volume of the connected speakers.
• AC Input: For connecting the provided AC power cord.
• Power Switch: On/Off toggle.
• Status LED: Indicates power and connection status.

Image: A close-up view of the Receiver's mode switch (Stereo, Bridge, Mono) and the volume control knob.

Image: Detailed view of the speaker output terminals on the Receiver, showing L+ and L- for the left channel, and R+ and R- for the right channel, with a "BRIDGE" indicator.

Setup Instructions

Follow these steps to set up your wireless surround sound system.

Step 1: Connect Antennas

Screw the provided wireless antennas onto the ANT ports of both the Transmitter (TX) and Receiver (RX) units. Ensure they are securely tightened.

Step 2: Connect Transmitter (TX) to Your A/V Receiver/Amplifier

Choose one of the following connection methods:

1. Speaker Level Input (Recommended for A/V Receivers):
   • Connect the speaker wires from the rear surround speaker outputs of your A/V receiver/amplifier to the "SPEAKER LEVEL IN" terminals on the TX unit.
   • Ensure correct polarity (+ to + and - to -).
2. Stereo RCA Input (Line In):
   • Connect RCA cables from the line-level audio outputs (e.g., Zone 2 out, Pre-out) of your A/V receiver or preamp to the "LINE IN" RCA ports on the TX unit.
3. Subwoofer Input (Optional):
   • If you wish to transmit a subwoofer signal, connect an RCA cable from the subwoofer output of your A/V receiver to the "SUBWOOFER IN" port on the TX unit.

Note: Adjust the ATT switch on the TX unit if the input signal is too strong or too weak. Start with 0dB and adjust if distortion or low volume occurs.

Step 3: Connect Receiver (RX) to Passive Speakers

Connect your passive rear surround speakers to the "SPEAKER OUTPUT" terminals on the RX unit using speaker wires. Ensure correct polarity.

• For stereo operation, connect left speaker to L+/L- and right speaker to R+/R-.
• For bridged mono operation (e.g., for a single, more powerful speaker), connect to the BRIDGE terminals. Refer to your speaker's impedance for compatibility.

Optional Subwoofer Connection: If you connected a subwoofer input to the TX unit, you can connect an active subwoofer or subwoofer amplifier to the "SUBWOOFER OUT" port on the RX unit.

Image: A comprehensive diagram showing how to connect the Transmitter to an A/V receiver (speaker level or line level) and the Receiver to passive rear speakers and an optional subwoofer, including power connections.

Step 4: Power On

Connect the 9V power adapter to the TX unit and plug it into a power outlet. Connect the AC power cord to the RX unit and plug it into a power outlet. Turn on both units using their respective power switches.

Operating Instructions

Pairing

The Transmitter and Receiver units are pre-paired at the factory. Upon powering on, the status LEDs on both units will blink blue and then turn solid blue, indicating a successful wireless connection. If they do not connect automatically, press the 'M' (Match) button on both units simultaneously for a few seconds until they pair.

Image: A close-up showing the blue LED indicator (top) and green LED indicator (bottom) on the units, which signify connection status.

Volume Adjustment

Use the "VOLUME" knob on the Receiver (RX) unit to adjust the output level of your rear speakers. It is recommended to set the volume to a moderate level and then fine-tune it using your A/V receiver's speaker level calibration.

Mode Selection (RX Unit)

The RX unit features a mode switch:

• Stereo: Standard stereo output for two rear speakers (L/R).
• Bridge: Combines the two amplifier channels into a single, more powerful mono output. Use this for a single, higher-power speaker.
• Mono: Provides a mono output to both L and R channels.

Select the appropriate mode based on your speaker configuration.

Troubleshooting

If you encounter issues, refer to the following common problems and solutions:

Specifications

Maintenance

To ensure the longevity and optimal performance of your Dynasty PROAUDIO WSA-5RP-PLUS system, follow these maintenance guidelines:

• Cleaning: Use a soft, dry cloth to clean the exterior surfaces of the units. Avoid using liquid cleaners, aerosols, or solvents.
• Ventilation: Ensure that the ventilation slots on both units are not obstructed to prevent overheating.
• Environment: Operate the units in a dry environment, away from direct sunlight, heat sources, and excessive moisture.
• Power: Disconnect power before cleaning or if the units will be unused for an extended period.

Warranty and Support

For warranty information, please refer to the warranty card included with your product or contact DYNASTY PROAUDIO customer support directly. For technical assistance or further inquiries, please visit the official DYNASTY PROAUDIO website or contact their customer service department.