VEVOR Motorcycle Rear Wheel Stand

1. Introduction

Thank you for choosing the VEVOR Motorcycle Rear Wheel Stand. This manual provides essential information for the safe and effective assembly, operation, and maintenance of your new stand. Designed for durability and ease of use, this stand is an indispensable tool for motorcycle enthusiasts and professionals alike, facilitating various maintenance tasks and secure storage.

Figure 1.1: VEVOR Motorcycle Rear Wheel Stand with U and L forks.

2. Safety Information

Always prioritize safety when using this product. Failure to follow these instructions may result in injury or damage to the motorcycle or stand.

• Ensure the stand is placed on a flat, stable, and non-slip surface.
• Verify the motorcycle's weight does not exceed the stand's maximum load capacity of 850 lbs (390 kg).
• Always secure the motorcycle properly on the stand before performing any maintenance.
• Do not attempt to move the motorcycle while it is on the stand unless the stand is designed for mobility and the path is clear.
• Keep hands and feet clear of moving parts during lifting and lowering operations.
• If using U-forks, ensure your motorcycle has swingarm spools installed.
• For safer operation, it is recommended to prop up the rear wheel first and then the front wheel if using both stands.

3. Parts List

Before assembly, ensure all components are present:

• 1 x Main Rear Stand Frame
• 1 x Pair of U-shaped Fork Heads (for spools)
• 1 x Pair of L-shaped Fork Heads (for swingarms)
• 4 x PP Casters (pre-installed or to be attached)
• Necessary Fasteners and Pins for assembly

Figure 3.1: U-type and L-type adapters for versatile motorcycle support.

4. Setup and Assembly

The VEVOR Motorcycle Rear Wheel Stand is designed for quick and straightforward assembly. Follow these steps:

1. Unpack all components and lay them out on a clean, flat surface.
2. Attach the PP casters to the designated points on the main stand frame if not pre-installed. Ensure they are securely fastened.
3. Select the appropriate fork heads (U-shaped for spools or L-shaped for swingarms) based on your motorcycle's setup.
4. Insert the chosen fork heads into the adjustable arms of the stand and secure them with the provided fasteners. Ensure the fasteners provide strengthening fixation.
5. Adjust the width of the stand to match your motorcycle's swingarm or spool width. The U-shaped fork head supports widths from 8.9-13.8 inches (225-350 mm), and the L-shaped fork head supports widths from 9.1-13 inches (230-330 mm).

Figure 4.1: Key features of the stand's robust construction, including 3-angle force points, thickened steel, PP casters, and strengthening fasteners.

Figure 4.2: Detail of the non-slip and non-abrasive U+L fork heads, ensuring secure contact with the motorcycle.

5. Operating Instructions

Using the VEVOR Motorcycle Rear Wheel Stand is designed to be quick and effortless:

1. Position the stand behind the motorcycle's rear wheel, aligning the fork heads with the swingarm or spools.
2. Ensure the motorcycle is stable and upright, preferably with assistance or using its side stand if applicable.
3. Firmly grasp the extended handle of the stand.
4. With a smooth, controlled motion, push down on the handle. The four 3-inch PP casters will facilitate an effortless lift, raising the rear wheel off the ground in approximately 2-3 seconds.
5. Once the motorcycle is securely lifted, ensure it is stable before proceeding with any work.

Figure 5.1: Step-by-step guide to quickly lift your motorcycle using the stand's casters and leverage.

Figure 5.2: The stand is applicable to most motorcycles, supporting up to 850 lbs. Examples include Dirt Motorcycles (220 lbs) and Sport Motorcycles (550 lbs). Note: Not suitable if the rear wheel fork is blocked.

Figure 5.3: Motorcycle securely lifted by the VEVOR Rear Wheel Stand, ready for maintenance.

6. Maintenance

Regular maintenance will prolong the life of your VEVOR Motorcycle Rear Wheel Stand:

• Cleaning: Wipe down the stand with a damp cloth after each use to remove dirt, grease, and debris.
• Inspection: Periodically inspect all fasteners, welds, and casters for any signs of wear, damage, or looseness. Tighten any loose bolts immediately.
• Lubrication: Apply a light lubricant to the caster axles and any pivot points to ensure smooth operation.
• Storage: Store the stand in a dry, clean environment to prevent rust and corrosion. Its compact design allows for convenient storage.

Long-term holding of your motorcycle on the stand will not compress the tires or cause flat spots and air leaks, making it ideal for extended storage.

7. Troubleshooting

If you encounter issues with your VEVOR Motorcycle Rear Wheel Stand, consider the following:

8. Specifications

Figure 8.1: Detailed dimensions and key specifications of the VEVOR Motorcycle Rear Wheel Stand.

9. Warranty and Support

For warranty information and technical support, please refer to the documentation included with your purchase or contact VEVOR customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.

For further assistance, visit the official VEVOR website or contact their support team through the contact information provided on their packaging or website.