Introduction
This manual provides essential information for the safe and effective use of your JIAJIESHI replacement battery, Model CS-MKT103VX (Part No. 196885-1). This battery is designed as a replacement for various Makita power tools. Please read this manual thoroughly before initial use and retain it for future reference.
Compatible Makita Models: CL103D, CL103DW, CL103DX, CL105D, CL105DW, CL105DWI, CL105DWN, CL105DWNI, CL105DWNP, CL105DWNR, CL105DWR, CL110D, CL110DW, CL110DWI, CL110DWR.
Safety Instructions
Failure to follow these safety instructions may result in fire, electric shock, or other injuries. Always exercise caution when handling batteries.
- Do not attempt to disassemble, open, or service the battery pack.
- Replace only with the battery pack designated for this product. Ensure compatibility by checking your device's model and original battery part number.
- Do not crush, puncture, short external contacts, or dispose of in fire or water.
- Do not store above 60°C (140°F).
- A new battery pack must be fully charged before use to reduce the risk of fire or burns.
- Read all instructions in the operating guide of your power tool before using the battery.
- Avoid using low-quality third-party adapter chargers, as they can shorten the battery's lifespan.
- The warranty is void if the product label is removed.
Image: Detailed view of the battery label, highlighting model number CS-MKT103VX, part number 196885-1, 10.8VDC, 2000mAh/21.60Wh, and critical safety warnings. For more information, visit cameronsino.com.
Setup
- Compatibility Check: Before installation, verify that the battery model (CS-MKT103VX) and part number (196885-1) match your device's requirements. Refer to your power tool's manual for specific battery compatibility.
- Initial Charging: For optimal performance, fully charge the new battery pack before its first use. A new battery typically achieves its best performance after 2 to 3 complete charge and discharge cycles.
- Installation: Carefully align the battery with the battery slot on your Makita power tool. Push the battery firmly until it clicks into place, ensuring the connector is properly and securely connected to your device.
Image: The JIAJIESHI replacement battery, illustrating its form factor for proper installation into compatible Makita tools.
Operating Instructions
Once installed and fully charged, the battery is ready for use with your compatible Makita power tool. Operate your tool according to its specific instruction manual.
- Always ensure the battery is securely seated in the tool before operation.
- Monitor the tool's performance; if power diminishes significantly, it's time to recharge the battery.
- Avoid completely draining the battery frequently, as this can reduce its overall lifespan.
Maintenance
- Charging: Use only chargers compatible with 10.8V Li-ion batteries. Avoid using unapproved or low-quality chargers.
- Storage: Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures (above 60°C / 140°F). For long-term storage, it is recommended to store the battery at approximately 50% charge.
- Cleaning: Keep battery contacts clean. Use a dry, clean cloth to wipe off any dust or debris.
- Disposal: Do not dispose of batteries in household waste. Follow local regulations for proper disposal of Li-ion batteries.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Charger malfunction; improper connection; battery too hot/cold. | Ensure charger is working and properly connected. Allow battery to reach room temperature before charging. |
| Short operating time | Battery not fully charged; battery nearing end of life; high power demand. | Ensure battery is fully charged. Perform 2-3 full charge/discharge cycles. Consider battery replacement if issues persist. |
| Battery not fitting tool | Incorrect battery model; improper alignment. | Verify battery compatibility with your tool model. Re-align and firmly insert the battery. |
If troubleshooting steps do not resolve the issue, please contact customer support.
Specifications
| Brand | JIAJIESHI |
| Model No. | CS-MKT103VX |
| Part No. | 196885-1 |
| Battery Type | Li-ion |
| Voltage | 10.8 Volts |
| Capacity | 2000mAh / 21.60Wh |
| Dimensions | 133.10 x 45.00 x 20.00mm |
| Weight | 150.0g |
| Reusability | Rechargeable |
| Certifications | FCC, CE, CB, ISO9332, RoHS |
| Manufacturer | ShenZhen HENZENS Technology Co., Limited |
Warranty and Support
This JIAJIESHI replacement battery is backed by a 14-day money-back guarantee and a 12-month warranty from the date of purchase.
If you encounter any questions or issues during the use of our product, please do not hesitate to contact our customer service. We are committed to providing prompt assistance and will reply as soon as possible.
For support, please refer to the contact information provided with your purchase or on the official JIAJIESHI product page.