1. Product Overview
This manual provides essential information for the safe and effective use of the Henhaoro CS-HNC300SL Ni-MH battery, designed as a replacement for Honeywell C300 alarm systems and compatible with part numbers 51199942-300, CC-SCMB02, and 143553.
The battery features a capacity of 4500mAh and operates at 3.6V, providing 16.20Wh of power. It is a Nickel Metal Hydride (Ni-MH) battery, known for its reliability and performance in alarm system applications.
Figure 1: Front view of the Henhaoro CS-HNC300SL battery, showing its green casing, attached black and red power wires, and the connector.
Figure 2: Top view of the battery, displaying the product label with detailed specifications and important safety warnings.
2. Safety Information
WARNING: To reduce risk of fire or burns, read instructions in operating guide before using the battery.
- Do not attempt to disassemble, open, or service the battery pack.
- Replace only with the battery pack designated for this product.
- Do not crush, puncture, short external contacts, or dispose of in fire or water.
- Do not store above 60°C (140°F).
- New battery pack must be fully charged before use.
This battery has undergone quality certification including ROSH, CE, and UL triple certification, ensuring safety and reliability. It incorporates protection against over-charge, over-discharge, over-heat, over-current, and short-circuiting.
3. Setup and Installation
This battery is designed for direct replacement in compatible Honeywell C300 alarm systems. Before installation, ensure the alarm system is powered off and disconnected from any external power sources.
- Locate the battery compartment in your Honeywell C300 alarm system. Refer to your alarm system's specific manual for exact location and access instructions.
- Carefully disconnect the old battery from its connector.
- Connect the new Henhaoro CS-HNC300SL battery to the system's battery connector. Ensure the connection is secure and properly aligned.
- Place the new battery securely within the battery compartment.
- Close the battery compartment cover.
- Reconnect the alarm system to its power source and power it on. The system may require a short period to recognize the new battery and begin charging.
Figure 3: Close-up view of the battery's connector, which should be securely attached to the alarm system's battery port.
4. Operating Instructions
Upon successful installation, the battery will begin charging when the alarm system is connected to its main power supply. Ni-MH batteries do not suffer from memory effect, allowing for flexible charging cycles.
- Initial Charge: It is recommended to fully charge the new battery before its first extended use.
- Normal Operation: The battery provides backup power to your alarm system during power outages or when the main power supply is interrupted.
- Discharge: The battery will automatically discharge to power the system when needed.
5. Maintenance
Proper maintenance ensures the longevity and optimal performance of your battery.
- Regular Checks: Periodically check the battery and its connections for any signs of damage or corrosion.
- Temperature: Store and operate the battery within recommended temperature ranges. Avoid extreme heat or cold. Do not store above 60°C (140°F).
- Cleaning: If necessary, gently clean the battery's exterior with a dry, soft cloth. Do not use liquids or abrasive cleaners.
- Long-Term Storage: If the battery will not be used for an extended period, store it in a cool, dry place. It is advisable to partially charge the battery before storage and recharge it every few months to prevent deep discharge.
6. Troubleshooting
If you encounter issues with your battery, consider the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Battery not charging | Loose connection, system power issue, faulty battery (rare) | Ensure battery is securely connected. Check alarm system's main power supply. If issues persist, consult alarm system manual or professional. |
| Short backup time | Battery not fully charged, aging battery, high power consumption by system | Allow battery to fully charge. Ensure system is not drawing excessive power. If battery is old, consider replacement. |
| System not recognizing battery | Incorrect installation, incompatible battery, system fault | Re-check installation steps. Verify battery model compatibility. Consult alarm system manual. |
7. Specifications
| Attribute | Value |
|---|---|
| Model No. | CS-HNC300SL |
| Part Numbers | 51199942-300, CC-SCMB02, 143553 |
| Category | Alarm System Battery |
| Capacity | 4500mAh |
| Type | Ni-MH (Nickel Metal Hydride) |
| Voltage | 3.6V |
| Rate | 16.20Wh |
| Color | Green |
| Dimension | 77.20 x 50.80 x 25.80mm |
| Net Weight | 245.0g / 8.64oz |
| Gross Weight | 315g / 11.11oz |
| EAN Code | 4894128182955 |
| Manufacturer | ShenZhen HENZENS Technology Co., Limited |
8. Warranty and Support
This Henhaoro battery is manufactured with high-quality components and undergoes rigorous testing to ensure performance and safety. It holds ROSH, CE, and UL triple certifications, indicating compliance with international safety and environmental standards.
The battery is designed with built-in protections against over-charge, over-discharge, over-heat, over-current, and short-circuit, contributing to its reliability and longevity. For specific warranty terms and conditions, please refer to the product packaging or contact Henhaoro customer support.
For technical support or inquiries, please visit the official Henhaoro store or contact their customer service channels. Always refer to your Honeywell C300 alarm system's manual for system-specific instructions and troubleshooting related to battery integration.