Allewie Queen Bed Frame Instruction Manual

Introduction

This manual provides detailed instructions for the assembly, operation, and maintenance of your Allewie Queen Velvet Upholstered Platform Bed Frame (Model AK-LE6017). Please read all instructions carefully before beginning assembly and retain this manual for future reference.

Safety Information

• Assemble the bed frame on a soft, clean surface to prevent damage.
• Ensure all parts are present before assembly. If any parts are missing or damaged, contact customer support.
• Do not fully tighten screws until all components are loosely assembled. This allows for easier alignment.
• Keep small parts away from children during assembly.
• It is recommended that two adults assemble this bed frame.
• Do not use power tools for assembly as this may overtighten screws and damage the frame.
• Periodically check and retighten all connections to ensure stability.

Package Contents

Verify that all components listed below are included in your package. Refer to the included installation manual for a detailed parts diagram.

Image: Overview of all bed frame components and hardware. This diagram illustrates the various parts, including the headboard, side rails, support legs, wooden slats, and assembly hardware.

• Upholstered Headboard
• Side Rails (Left and Right)
• Footboard
• Center Support Beam
• Support Legs
• Wooden Slat Roll
• Hardware Pack (screws, bolts, washers, Allen wrench)
• Installation Manual

Setup and Assembly

Follow these steps to assemble your Allewie Queen Bed Frame. It is recommended to have two people for assembly.

1. Step 1: Attach Headboard Legs

   Attach the headboard support legs to the upholstered headboard using the provided bolts and washers. Do not fully tighten the bolts at this stage.

   

   Image: Detailed view of the headboard assembly process, illustrating how the support legs connect to the main headboard panel.

2. Step 2: Assemble Side Rails and Footboard

   Connect the side rails to the headboard and footboard using the appropriate hardware. Ensure the connection points are aligned correctly. Loosely secure all bolts.
3. Step 3: Install Center Support Beam and Legs

   Place the center support beam along the length of the frame. Attach the support legs to the center beam and the frame as indicated in your detailed manual. Ensure all legs are securely attached and provide even support.

4. Step 4: Install Wooden Slats

   Unroll the wooden slat set across the bed frame. The slats are often connected by Velcro or fabric straps for easy placement. Secure the slats to the side rails using the pre-drilled holes and screws, if applicable. Ensure the slats are evenly spaced and firmly in place to support the mattress.

   

   Image: Close-up view of the wooden slats being installed onto the bed frame, highlighting the Velcro attachment for stability and noise reduction.
5. Step 5: Final Tightening

   Once all components are in place and aligned, systematically tighten all bolts and screws using the provided Allen wrench. Do not overtighten. Ensure the frame is stable and level.

Operating Instructions

Adjusting the Headboard Height

The Allewie Queen Bed Frame features an adjustable headboard, allowing you to customize its height to suit your mattress thickness and preference. The headboard can be adjusted between 47 inches and 51 inches in height.

1. To adjust the headboard, locate the bolts connecting the headboard to its support legs.
2. Loosen these bolts slightly, but do not remove them completely.
3. Carefully slide the headboard up or down to your desired height.
4. Once the desired height is achieved, firmly tighten the bolts to secure the headboard in position.

Image: Diagram showing the adjustable headboard mechanism, with height options of 47 inches and 51 inches. This illustrates how to raise or lower the headboard.

Maintenance

Cleaning Instructions

• For general cleaning, wipe the bed frame with a dry, soft cloth.
• For velvet upholstery, gently vacuum with an upholstery attachment to remove dust and debris.
• Avoid using harsh chemicals, abrasive cleaners, or excessive moisture, as these can damage the velvet fabric and frame finish.
• Spot clean spills immediately with a clean, damp cloth and mild soap, then blot dry. Test any cleaning solution on an inconspicuous area first.

General Care

• Periodically check all bolts and screws to ensure they remain tight. Retighten as necessary to maintain stability and prevent squeaking.
• Avoid dragging the bed frame when moving it; lift it to prevent damage to the legs and frame structure.
• Do not exceed the maximum weight capacity of 800 pounds.

Troubleshooting

Specifications

Image: Detailed dimensions of the Allewie Queen Bed Frame, including length, width, and adjustable headboard height.

• Model: AK-LE6017
• Size: Queen
• Color: Pink
• Upholstery Fabric Type: Velvet
• Product Dimensions (L x W x H): 83.3" x 62.4" x 47"/51" (Adjustable Headboard)
• Brand: Allewie
• Included Components: Frame, Headboard, Installation Manual, Slat
• Finish Type: Wooden
• Weight Limit: 800 Pounds
• Item Weight: 67.9 Pounds
• Assembly Required: Yes
• Form Factor: Platform Bed
• Ground To Item Distance: 7.9 Inches
• Recommended Mattress Thickness: 8-14 inches
• Box Spring Required: No (Box spring optional)
• UPC: 749655394569

Warranty and Support

Returns Policy

This product is eligible for a 30-day easy return policy. Please refer to your purchase platform's return guidelines for detailed information on initiating a return or exchange.

Customer Support

For any questions, concerns, or assistance with your Allewie bed frame, please contact Allewie customer support. Contact information can typically be found on the Allewie brand store page or through your purchase platform's customer service portal.

You can visit the official Allewie Store for more information: Allewie Store