PRIMECOMTECH Tesla Gen 2 Wall Connector Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of your PRIMECOMTECH Tesla Gen 2 Wall Connector, Model 1050067. This device is designed to provide high-power charging for Tesla Model S, 3, X, and Y electric vehicles.

Please read this manual thoroughly before installation and use. Retain this manual for future reference.

Figure 1: Front view of the PRIMECOMTECH Tesla Gen 2 Wall Connector, showing its sleek design and charging cable.

2. Safety Information

WARNING: Installation of this product involves high voltage electricity. Improper installation can result in serious injury, death, or property damage. Installation must be performed by a qualified electrician in accordance with all local and national electrical codes and regulations.

• Do not attempt to install or repair the Wall Connector yourself unless you are a qualified electrician.
• Ensure the main power supply is disconnected before any installation or maintenance work.
• Do not use the Wall Connector if it is damaged, cracked, or shows any signs of wear.
• Keep children and pets away from the Wall Connector during operation.
• Operate the Wall Connector only within its specified electrical ratings.

3. Package Contents

Carefully unpack the box and ensure all items are present and undamaged. If any items are missing or damaged, contact customer support immediately.

• PRIMECOMTECH Tesla Gen 2 Wall Connector (with integrated charging cable)
• Mounting Hardware
• Instruction Manual (this document)

Figure 2: Contents of the PRIMECOMTECH Tesla Gen 2 Wall Connector package, including the main unit and mounting accessories.

4. Setup and Installation

IMPORTANT: Installation of the PRIMECOMTECH Tesla Gen 2 Wall Connector requires professional electrical knowledge. It is strongly recommended that a certified electrician performs the installation to ensure safety and compliance with all applicable electrical codes.

4.1 Site Selection

• Choose a location near your vehicle's parking spot, ensuring the charging cable can comfortably reach the charging port.
• The Wall Connector can be installed indoors or outdoors. Ensure the chosen location is protected from direct impact and excessive moisture.
• Mount the unit at a height that allows for easy access and cable management.

4.2 Electrical Requirements

• The Wall Connector requires a dedicated circuit.
• Compatible with 110/220V & 120/240V dual-phase service (200+ Amp electrical system recommended).
• Also compatible with 277/480V commercial/industrial 3-phase AC systems.
• Circuit breaker size should be selected based on desired charging current (60A, 70A, 80A, 100A options available for configuration by the electrician).

4.3 Mounting the Wall Connector

1. Mark the drilling locations using the provided mounting template (if applicable) or by measuring the unit.
2. Drill pilot holes and secure the mounting bracket to the wall using the supplied mounting hardware.
3. Attach the Wall Connector unit to the mounted bracket.

4.4 Electrical Wiring

This step must be performed by a qualified electrician. Refer to the detailed wiring diagrams provided with the product packaging for specific connections. Ensure proper grounding and adherence to all safety protocols.

5. Operating Instructions

Once installed by a qualified electrician and power is supplied, the Wall Connector is ready for use.

1. Connect to Vehicle: Open your Tesla vehicle's charge port. Grasp the Wall Connector handle and firmly insert it into the vehicle's charge port. The vehicle will indicate a successful connection.
2. Charging Status: The LED indicator on the Wall Connector will illuminate to show charging status. Refer to your vehicle's display for detailed charging information.
3. Disconnect: When charging is complete, or you wish to stop charging, press the button on the Wall Connector handle to release the latch, then pull the handle out of the vehicle's charge port. Return the charging cable to its holder on the Wall Connector.

Figure 3: Tesla Wall Connector actively charging a Tesla vehicle, demonstrating typical usage.

5.1 Charging Performance

• Up to 70 miles of range per hour for Model S & X (with appropriate vehicle configuration).
• Up to 45 miles of range per hour for Model 3 & Y (max 48 Amp / 11KW).
• Maximum output: 20 kW / 80 Amps.

6. Compatibility

The PRIMECOMTECH Tesla Gen 2 Wall Connector is compatible with all Tesla vehicles:

• Tesla Model S
• Tesla Model 3
• Tesla Model X
• Tesla Model Y

Note: Tesla Model 3 and Model Y will charge at a maximum of 48 Amps (11KW), regardless of higher Wall Connector output settings.

Figure 4: A Tesla Model S being charged by the Wall Connector in a residential setting.

7. Specifications

8. Maintenance

The PRIMECOMTECH Tesla Gen 2 Wall Connector is designed for minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

• Cleaning: Periodically wipe the exterior of the Wall Connector with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off before cleaning.
• Cable Inspection: Regularly inspect the charging cable and connector for any signs of damage, fraying, or wear. If damage is observed, discontinue use and contact a qualified electrician for inspection or replacement.
• Storage: When not in use, ensure the charging cable is neatly coiled and stored on its holder to prevent tripping hazards and damage.

9. Troubleshooting

If you encounter issues with your Wall Connector, refer to the following common troubleshooting steps:

• No Power/No Charging:
  • Check the circuit breaker connected to the Wall Connector. Reset if tripped.
  • Ensure the Wall Connector is properly connected to the electrical supply. (Requires electrician verification).
  • Verify the charging cable is securely plugged into both the Wall Connector and the vehicle.
• Slow Charging:
  • Confirm your vehicle's charging settings are configured for maximum amperage.
  • Ensure the Wall Connector's internal settings (configured during installation) match the desired amperage and circuit capacity.
  • Note that Model 3 and Y vehicles have a maximum charging rate of 48 Amps (11KW) from the Wall Connector.
• Connector Not Latching:
  • Ensure the vehicle's charge port is clean and free of debris.
  • Apply firm, even pressure when inserting the connector.
  • If the issue persists, inspect the connector for physical damage.

For issues not resolved by these steps, or for any electrical concerns, contact a qualified electrician or PRIMECOMTECH customer support.

10. Warranty and Support

Return Policy: This item can be returned in its original serial number and original condition for a full refund or replacement within 30 days of receipt. A partial or no refund may be issued for used, damaged, or materially different returns.

For technical support or further assistance, please refer to the contact information provided with your purchase documentation or visit the PRIMECOMTECH official website.